An aluminum tube of 3-in. outside diameter is to carry a load P of 10 kips having an eccentricity e = 0.6 in. Knowing that the stock of in. up to 1⁄in., determine tubes available for use are made of aluminum alloy 2014-T6 and have wall thicknesses in increments of the lightest tube that can be used. Use the allowable-stress method. (Input the final answer as a fraction.) e = 0.6 in. 6 ft B e -3-in. outside diameter The lightest tube that can be used should have a wall thickness of (/) in.

An aluminum tube of 3-in. outside diameter is to carry a load P of 10 kips having an eccentricity e = 0.6 in. Knowing that the stock of in. up to 1⁄in., determine tubes available for use are made of aluminum alloy 2014-T6 and have wall thicknesses in increments of the lightest tube that can be used. Use the allowable-stress method. (Input the final answer as a fraction.) e = 0.6 in. 6 ft B e -3-in. outside diameter The lightest tube that can be used should have a wall thickness of (/) in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m
_Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. C°) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 T1.2 195 3 35 Aluminium 300 18.9 4 30 90 Aluminium Steal 4m 2m
An aluminum [E = 9100 ksi] control rod with a circular cross section must not stretch more than 0.23 in. when the tension in the rod is 2100 lb. If the maximum allowable normal stress in the rod is 10.9 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d = (b) L = i i in. in.
If the gauge is made of a material having a yield stress equal 200 MPa, determine the minimumrequired diameter d. Using a factor of safety (F.S. = 2)
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
The aluminum and bronze cylinders are centered and secured between two rigid end-plates by tightening the two steel bolts. There is no axial load in the assembly at a temperature of 50°F. Find the stress in the steel bolts when the temperature is increased to 200°F. Use the following data: A (in.²) a (/°F) E (psi) Aluminum cylinder 2.00 12.8 × 10–6 10 × 106 Bronze cylinder 3.00 10.5 × 10–6 12 × 106 Each steel bolt 0.75 6.5 × 10–6 29 × 106 1.0 in. -3 in.→ →-4 in. F1.0 in. Aluminum Bronze
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
PROBLEM 2 A tri metallic bar is uniformly compressed by an axial force P-12KN applied through a rigid end plate The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter l0mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm E for steel =210Gpa, E for brass = 100GPA and E for copper is 120GPA Calculate the compressive stress of each metal due to force P
7 30 Enercise:- diameter of 12mm A cylindrical rod 100 mm long with is subjected to a 30000 N. Assuming that the tensile load of deformation is entirely elastic and allowable elevation in pligmeter is allowable reduction in dligmeter is 0.015mm. choose amory only meeting requirent U (Poiss ons vahu) 0.33 below Material Aluminium alloy Bronze Titanium allow manimum 0.3 mm while manimum E (GPa) 70 100 110 0.34 3
A typlcal aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 200 mm and the wall thickness is 12 mm. If the air In the tank is pressurized to 16MP3, determine the maximum shear stress in the plane of the cylinder wall. O 29.3 MPa O 33.7 MPa O 27.4 MPa O 40.7 MPa O 21.0 MPa
A cylindrical assembly consisting of a brass core and an aluminum collaris compressed by a load P (see figure). The length of the aluminum collarand brass core is 350 mm. the diameter of the core is 25 mm, and theoutside diameter of the collar is 40 mm. Also, the module of elasticity ofthe aluminum and brass are 72 GPa and 100 GPa, respectively.(a) If the length of the assembly decreases by 0.1% when the load Pisapplied, what is the magnitude of the load?(b) What is the maximum permissible load f^ if the allowable stresses inthe aluminum and brass are SO MPa and 120 M Pa, respectively?
Prob 02: The two rods are used to support a crate with weight of 2kN. The rod are made of the same material and of the same diameter. If the failure tensile normal stress for this material is 200 mPa, what is the minimum required diameter for the rods in mm? (2 points) 45° 30°