Stress-Strain Behavior 6.3 A specimen of copper having a rectangular cross section 15.2 mm × 19.1 mm (0.60 in. × 0.75 in.) is pulled in tension with 44,500 N (10,000 lb;) force, producing only elastic deformation. Calculate the resulting strain.

Stress-Strain Behavior 6.3 A specimen of copper having a rectangular cross section 15.2 mm × 19.1 mm (0.60 in. × 0.75 in.) is pulled in tension with 44,500 N (10,000 lb;) force, producing only elastic deformation. Calculate the resulting strain.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Related questions

Q: The stress-strain relation of an aluminum alloy bar having a length of 2 m and a diameter of 10 mm…

A: Calculate stress by using the following equation: σ=Pπ4d2 Here, Load applied on the rod is P and…

Q: Q1) A specimen with the given dimension is loaded as given in the figure below. Determine; a) The…

A: As per the guidelines of Bartleby we are supposed to only answer the first three subparts of the…

Q: A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If…

A: It is required to determine the stress in the rod. Here, P is the load and A is the area of the…

Q: The modulus of elasticity of 30mm diameter aluminum bar was 80 Gpa, calculate the strain and the…

Q: A metal rod with 0.5 in. diameter is subjected to 2000 lb tensile load. Calculate the resulting…

A: The given data is shown below:

Q: A rod of dimension 20 mm x 20 mm is carrying an axial tensile load of 10 kN. If the modulus of…

A: given force F=10 kNE=250 MPacross section area A=20 mm×20 mm

Q: A steel bar 4 inches long and having a square cross section 0.8 inches on an edge is pulled in…

Q: Q5) A specimen of alloy having a rectangular cross section of dimensions 5 mm x 16 mm is deformed in…

A: Given:- dimensions-5mm x 16mm To find:- a)Modulus of elasticity b)Yield strength c)The modulus of…

Q: The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length…

Q: The stress-strain curve of an alloy is given below. Calculate the modulus of toughness. 14 12 10…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: The following figure shows the tensile stress-strain curve for a plain-carbon steel. 600 80 500 MPa…

A: a) Ultimate tensile strength is 580 MPa (Approximately).

Q: A rod with a length of 1 m and a radius of 20 mm is made of high-strength steel. The rod is…

A: Solution: Given that : Length of rod = 1m = 1000mm Radius of rod = 20 mm Diameter of rod = 40 mm…

Q: If a bronze model railroad track is 26 in. long and the ends are restrained from moving when the…

A: E=15 * 106 Psi Coeff of thermal expansion=9.6 * 10-6 /oF Change in temperature =40oF

Q: A tension test performed on a metal specimen to fracture produced the stress- strain relationship…

A: From the above graph, linear portion is up to the point where stress is equivalent to 50 ksi, and…

Q: ng steel bars, which was given a tensile strength of 45150 N, elongated by 2.1 mm, cross-strain was…

A: Given:- elongation=2.1mm E=200000MPa Poisson's ratio = 0.32 strain = 0.00056 To find:- a)L b)A

Q: 9 A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa, and an elastic…

Q: A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength…

A: Given: Gauge length = 100 mm Diameter = 10 mm Yield strength = 150 MPa Tensile load = 5.85 kN New…

Q: A copper rod 400mm long is pulled in tension to a length of 401.2 mm by applying a tensile stress of…

A: Given data, Length of copper rod= 400mm Extended length= 401.2mm Change in length = 401.2-400…

Q: Question No.2 Figure P1.16 shows the stress-strain relations of metals A and B during ten- sion…

A: It is that point on stress-strain curve, till which stress is linearly varying with strain. As per…

Q: A cylindrical piece of steel 80 mm dia and 120 mm long is subjected to an axial compressive force of…

Q: A specimen of steel has a rectangular cross section 20 mm wide and 40 mm thick, an elastic modulus…

A: solution Given tension P =60000N cross section =20mm×40mmelastic modulus E=207Gpa=207000Mpa…

Q: A cube made of an alloy with dimensions of 50 mm x 50 mm x 50 mm is placed into a pressure chamber…

Q: 22: What is the minimum thickness of a spherical steel tank if the diameter is 96 in, internal…

Q: Figure P1.18 shows (i) elastic-perfectly plastic and (ii) elastoplastic with strain hardening…

A: Given: The stains are 0.001 and 0.004. Consider the below figure,

Q: A steel bar with a length of 3 m, diameter of 25 mm, modulus of elasticity of 207 GPa, and linear…

A: Given: The length of the steel bar is 3 m. The diameter of the steel bar is 25 mm. The modulus of…

Q: A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to tension, with the results…

A: Given: Diameter of steel bar d, is 19 mm. Gauge length l, is 75 mm. The table is given below,

Q: A metal specimen 36mm in diameter has a length of 360 mm. A force of 300 kN elongates the length by…

Q: A metal specimen 36-mm in diameter has a length of 360 mm. A force of 300 KN elongates the length by…

Q: A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus…

A: Yield Strength: It is defined as the stress that a material can withstand without any permanent…

Q: A cube made of an alloy with dimensions of 50 mm * 50 mm * 50 mm is placed into a pressure chamber…

A: Given data: Since pressure applied uniformly on all sides of the cube:

Q: A cube made of an alloy with dimensions of 50mm×50mm×50mm is placed into a pressure chamber and…

Q: Determine the diameter of a steel rod that will carry a tensile load of 50,000kg at a stress of…

Q: A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a…

Q: An aluminum rod 20 mm in diameter and 5 m long is subjected to an axial tensile load of 50 kN…

Q: A tension test performed on a metal specimen to fracture produced the stress-strain relationship…

Q: Given that a steel cylinder of dimensions 12.0 mm in diameter and 70 mm long is subjected to…

A: (a) The modulus of elasticity is the slope of the line. E=∆σ∆z=200-00.001-0=2.0×105 MPa Therefore,…

Q: The stress-strain diagram for a metal alloy having an original diameter of 16 mm and a gauge length…

A: In this question , We calculate approximately Elastic modulus , yielding load and ultimate load…

Q: A rod with a length of 1 m and a radius of 20 mm is made of high-strength steel.The rod is subjected…

A: Given data:

Q: A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is…

A: Modulus of elasticity can be defined as the ratio of the stress experienced by a body or in a body…

Q: A steel column is 3 mm long and 0.4 m in diameter. It carries a load of 50 MN. Given that the…

Q: A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus…

A: Given: Yield strength of brass alloy is 280 MPa. Tensile strength of brass alloy is 390 MPa. Elastic…

Q: Question 1: A 25mm diameter aluminum rod is loaded axially in tension with a load of 100kN. The rod…

Q: A cylindrical specimen of undeformed brass that has a diameter of 300 mm is elastically deformed to…

Q: A force of 100,000 N is applied to an iron bar with a cross-sectional area of 10 mm × 20mm and…

A: The pressure that deforms the material in order to reduce the volume of the material is the…

Q: Given that a steel cylinder of dimensions 12.0 mm in diameter and 70 mm long is subjected to…

A: (a)

Q: A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength…

A: aWe knowΔL=PLAE0.1=5.851000100π4102EE=74,485Nmm2E=74,485Mpa

Q: A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing machine until the…

Q: Q1/ Consider the brass alloy for which the stress-strain behavior is shown in the figure below. A…

A: (a) Calculate the elongation as; Stress=EBrass×StrainForceArea=EBrass×∆LL2250…

Question

Stress-Strain Behavior
6.3 A specimen of copper having a rectangular cross
section 15.2 mm × 19.1 mm (0.60 in. × 0.75 in.) is
pulled in tension with 44,500 N (10,000 lb;) force,
producing only elastic deformation. Calculate the
resulting strain.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to ten- sion, with the results shown in Table P3.27. Using a computer spreadsheet pro- gram, plot the stress-strain relationship. From the graph, determine the Young's modulus of the steel and the deformation corresponding to a 150-kN load. TABLE P3.27 Load, kN Deformation, mm 54 0.084 163 0.168 284 0.336 330 1.428 366 3.360
S Figure P1.16 shows the stress-strain relations of metals A and B during ten- sion tests until fracture. Determine the following for the two metals (show all calculations and units): a. Proportional limit b. Yield stress at an offset strain of 0.002 m/m. c. Ultimate strength d. Modulus of resilience e. Toughness f. Which metal is more ductile? Why? 900 Metal A 600 Metal B 300 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 Strain, m/m FIGURE P1.16 Stress, MPa
4. A 2.0 m steel is being subjected into a tensile test. At force 30 kN, the length of the steel is now 2.2 m, but after the force has been released, the steel returned to 2.1 m. The state of the steel is at?
I5 In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in & total length 8 in) had a 0.2% offset yield strength of 80.000 psi and engineering strain of 0.010 at the yield strength point Calculate: The load (force) at this point. The instantaneous area of the specimen at this point. c. The true stress at this point. d. The true strain at this point. e. The total length of the specimen. if the load is released at this point.
PROBLEM 1 A steel rod with a cross sectional area of 150 mm? is stretched between two fixed points. The tensile load at 20°C is 5000 N. a.) What will be the stress at -20°C? b.) At what temperature will the stress be zero? Assume a = 11 .7 µm/m°C, and E = 200 Gpa *Show geometry of deformation ©sidewar
1.17 Figure P1.17 shows the stress-strain relations of metals A and B during tension tests until fracture. Determine the following for the two metals (show all calcu- lations and units): a. Proportional limit b. Yield stress at an offset strain of 0.002 in./in. 150 - - Metal A 100 • Metal B 50 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 Strain, in./in. FIGURE P1.17 c. Ultimate strength d. Modulus of resilience e. Toughness f. Which metal is more ductile? Why? Stress, ksi
A specimen of steel has a rectangular cross section 20 mm wide and 40 mm thick, an elastic modulus of 207 GPa, and a Poisson's ratio of 0.30. If this specimen is pulled in tension with a force of 60,000 N, what is the change in width if deformation is totally elastic? O Increase in width of 3.62 x 10-6 m O Decrease in width of 7.24 x 10-6 m Increase in width of 7.24 x 106 m O Decrease in width of 2.18 x 10-6 m
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?