A steel bar with a length of 3 m, diameter of 25 mm, modulus of elasticity of 207 GPa, and linear coefficient of thermal expansion of 0.000009 m/m/°C is fixed at both ends when the ambient temperature is 40°C. If the ambient temperature is decreased to 15°C, what internal stress will develop due to this temperature change? Is this stress tension or compression? Why?

A steel bar with a length of 3 m, diameter of 25 mm, modulus of elasticity of 207 GPa, and linear coefficient of thermal expansion of 0.000009 m/m/°C is fixed at both ends when the ambient temperature is 40°C. If the ambient temperature is decreased to 15°C, what internal stress will develop due to this temperature change? Is this stress tension or compression? Why?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Similar questions

A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa. What should be the thickness of the pipe? 0 9.78 mm O 11.56 mm O 12.35 mm O 10.55 mm
PROBLEM 1 A steel rod with a cross sectional area of 150 mm? is stretched between two fixed points. The tensile load at 20°C is 5000 N. a.) What will be the stress at -20°C? b.) At what temperature will the stress be zero? Assume a = 11 .7 µm/m°C, and E = 200 Gpa *Show geometry of deformation ©sidewar
If a bronze model railroad track is 26 in. long and the ends are restrained from moving when the temperature rises 40 °F, what is the stress that results? (Look up the coefficient of thermal expansion and modulus of elasticity.)
2.) Answer the following: a.) a 22 ft long solid steel rod is subjected to a load of 15,000 lb. This load causes the rod to stretch 0.435 in. The modulus of elasticity of the steel is 30,000,000 psi. Determine the diameter of the rod. b.) A solid circular titanium control rod must support an axial tension force of 12,000 lb. Assume that the modulus of elasticity of the titanium in 16,500,000 psi. If the rod must elongate no further than 0.35 in. when the normal stress of the rod is 68,000 psi, determine the minimum rod diameter AND the maximum rod length.
Prove that Young's modulus of a wire is equal to the stress necessary to double its length.
A 19-mm reinforcing steel bar and a gauge length of 75 mm was subjected to ten- sion, with the results shown in Table P3.27. Using a computer spreadsheet pro- gram, plot the stress-strain relationship. From the graph, determine the Young's modulus of the steel and the deformation corresponding to a 150-kN load. TABLE P3.27 Load, kN Deformation, mm 54 0.084 163 0.168 284 0.336 330 1.428 366 3.360
a) What is the stress in the bronze rod (in MPa)?b) What is the stress in the steel rod (in MPa)?
A steel bar is 10mm diameter and 4m long. If the temperature drops by 12°C and a = 11.7 um/m°C, what is the bar's thermal deformation? CLAT
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If Poisson's ratio is 0.25 and Young's modulus is 200 GPa, an increase in volume will be
If the material is subjected to triaxial stress, What does each principal stress contribute?
The lower end of a pole is a 3m long steel tube. It is joined to a 2.1 m long bronze tube. Compute the total elongation of the composite pole after a 15.15° rise in temperature. The steel part is 50 mm in outside diameter & 3mm thick while the bronze part which fits snugly in the steel tube is 3.2 mm thick. What compressive force is needed to return the pole to its original length? What will be the stresses in the steel & in the bronze after this force is applied? Neglect the length of splive/joint. For steel, use: a = 11.7 x 10-6 m/m, E = 210 GPa; & for bronze; a = 18.9 x 10-6 m/m, E = 83 GPa.