A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm X15.9 mm is deformed in tension. Use the load-elongation characteristics shown in thefollowing table to answer the following questions.Load0 4,740 9,140 12,920 16,540 18,300 20,170 22,900 25,070 26,800 28,640 30,240 31,100 31,280 30,820 29,180 24,140 18,970(N)1) Whatis theLength 75 75.025s 75.05 75.075 75.113 75.15 75.225 75.375 75.525 75. 75 76.57879.58181.5848788.725(тm)magnitude of modulus of elasticity?2) What is the magnitude of Ultimate tensile strength of this alloy.3) What is the magnitude of The ductility in percent elongation?Determine the indices for the vectors shown in the following figure:+21) indices for the vectors ABA.2) indices for the vectors B3) indices for vector c

Modulus of elasticity can be defined as the ratio of the stress experienced by a body or in a body…

A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is deformed in tension. Use the load-elongation characteristics shown in the following table to answer the following questions.

A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is deformed in tension. Use the load-elongation characteristics shown in the following table to answer the following questions.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 29P: A structural member with a rectangular cross section as shown in the accompanying figure is used to...

See similar textbooks

Related questions

Q: A steel rod 30 mm in diameter and 800 mm long has an allowable elongation not to exceed 1.5 mm, find…

Q: of the of curvature gnitude of the total ad of the car is the same ius of curvature Pg of t mass…

Q: 01// An interior Two-way slab panel 6.0 m * 7.2m carry a live load 10 kN/m². The slab thickness is…

Q: A -2.8% grade meets a 5.3% grade at a vertex (El. 141.94m) directly under an overpass bridge having…

A: G1 = -2.8% G2 = 5.3%

Q: 52. If the unsupported length of a stanchion is 4 meters and least radius of gyration of its cross-…

A: Given : Unsupported length of stanchion = 4 m = 400 cm Least radius of gyration = 5 cm

Q: A rectangular plane surface of width 2 m and height 3 m is placed vertically in water. What will be…

Q: Classify the soil by IS classification Given:- Liquid limit=22% Plasticity limit=19% Percentage…

Q: ce in members BD, CD and s shown. B D -12- -12- E 19

Q: 2. Given the following rectangular coordinates, calculate the vertical section of the survey point…

Q: Consider (Figure 1) Figure 60 20 ft ▼ Part A Determine the minimum initial velocity up at which the…

Q: Problem 7 - 72 Air at 1500 kPa absolute flows in a 25-mm-diameter tube. What is the maximum laminar…

A: The critical value for Reynolds number for which the flow can be laminar in case of pipe flow is…

Q: a speed of (50 cm/sec) through the first section of a pipe with a diameter of (25 cm). The diameter…

Q: Determine the reactions and draw the shear and moment diagram 90 kN A 2m 5m m 50 kN/m 6m El=constant

Q: For the symmetric parabolic arch with three joints: a) Write the mathematical equation defining the…

A: xC = 8 m xE = 60 - 9 = 51m L = 60m h = 13m

Q: A rectangular footing is to be used to support a 300 x 400 (400mm side is parallel to the long…

Q: 8-30. Determine the slope at B and the displacement at C. El is constant. Use the moment-area…

A: Given: Beam with the above loading conditions

Q: This is the corresponding tensile stress (MPa) at the minimum strain (as allowed by NSCP2015) of…

Q: 3/59 The standard test to determine the maximum lat- eral acceleration of a car is to drive it…

A: step 1-

Q: Es width of 2 m relative densit

A: given:

Q: Write an official letter to the authorities responsible for the provision and service of water…

A: Brief concept introduction- water supply- Water supply in any region is a very very crucial aspect…

Q: A wide, clean-earth river has a flow rate q = 150 ft³/s per foot. (a) What is the critical depth, Yc…

Q: ACTIVITY 3- Beam Analysis Analyze the loaded beam as shown. Be guided as follows: a. Solve for the…

Q: A 1.80m x 1.20m x 0.4m footing with a column at the center is loaded with a column at the center is…

A: Solution: Given: P = 750 kN M = 290 kNm Footing size = 1.8 x 1.2 depth = 400 mm Depth below G.L to…

Q: stimate the elastic settlement proposed by Mayerhof. Then, stimate the elastic settlement proposed…

A: Given:- 1.7m x 2.2m N60=52 To find:- consolidation settlement

Q: 25. An activated sludge system is designed to treat population of 50 000. The wastewater that enters…

Q: med to the wall by a spr m.

A: given:

Q: Find H in the figure for Q3 = 20 L/s, μ = 5x10-³ Pa and sp.gr. = 0.9. H 70 m 50 mm diam. ph -0.006 m…

Q: The center panel of the truss contains two flexible cables. What load P will cause a compressive…

Q: A groundwater sample was found to contain 500 mg/L total dissolved solids (TDS). TDS (in %) present…

A: given total dissolved solids-TDS=500 mg/L

Q: rapezoidal irrigation canal has a bottom width of 2m and a flow depth of 0.9m. The sides have a…

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

Q: Q1: Choose the correct answer for the following: 1- While selecting the location of an intake for…

Q: When the stress is removed, the material returns to the dimension

A: Deformation : change in size or shape of an object is referred to as deformation. The absolute…

Q: a) Draw a neat sketch of Activated Siudge Process and discuss how ȘVI, return sludge wasted sludge…

A: Activated Sludge Process- The activated sludge method employs highly concentrated microorganisms to…

Q: Obtain the general solution of the DE: (xy + x) dx = (x²y² + x² + y² + 1) dy x)dx…

A: Given data: xy+xdx=x2y2+x2+y2+1dy

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

A: Given data: E = 200 GPa = 2×108 kN/m2 I = 39.9 ×10-6 m4 Steps: 1. To determine support reaction 2.…

Q: Compute SN₂ for the flexible layers consisting of an asphalt concrete surface, a crushed- stone…

Q: PROBLEM: An A50 steel truss is subjected to dead loads as shown. REQUIRED: Investigate the adequacy…

A: AL150 = (150 + 150 - 8)*8 = 2336mm2 AL100 = (100 + 100 - 10)*10 = 1900 mm2 fy = 345 N/mm2 So, fall =…

Q: Q4: Determine the size of the intake structure with 1 unit using the following data: Discharge: 3.5…

A: given Intake structure with 1 unit-Discharge Q=3.5 m3/minminimum depth of water H=4 mLow water level…

Q: Water flows over a concrete spillway into a rectangular channel 9 m wide through a hydraulic jump.…

Q: 8-26. Determine the displacement at C and the slope at B. El is constant. Use the moment-area…

Q: 1. Two observation wells have been constructed in the formation shown. The flow rate is 0.01 m³/hr,…

A: The given figure is shown below:

Q: A horizontal beam 16 ft long is subjected to a load of 500 lb located to its center. The dimension…

A: Given: Beam with point load at center Beam dimensions To find: Flexural stress Notations; M =…

Q: The porosity (n) and the degree of saturation (S) of a soil sample are 0.7 and 40%, respectively. In…

A: Given data- Porosity n=0.7Degree of saturation S=40%=0.40Volume of soil V=100 m3To Find-Volume of…

Q: 6. Which are the legal and social responsibilities that an engineer needs to have at the moment to…

A: Social responsibilities are a part of all professions. The profession of engineering is no…

Q: Calculate the moment of inertia of the shaded area about the x-axis. A) Ix= 6.12(10^6) mm^4 B) Ix=…

Q: Part 1: Some Discrete Probability Distributions 4.2 Discrete Uniform Distribution 4.3 Binomial…

A: in this question , 3 examples is asked about probability

Q: The consumptive requirements of a crop are 0.2 cm per day for days 1 to 15, 0.3 cm per day for days…

Q: the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

Q: 1. Given the following survey data, calculate the ATVD, ANorth and AEast using th average angle and…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm X
15.9 mm is deformed in tension. Use the load-elongation characteristics shown in the
following table to answer the following questions.
Load
0 4,740 9,140 12,920 16,540 18,300 20,170 22,900 25,070 26,800 28,640 30,240 31,100 31,280 30,820 29,180 24,140 18,970
(N)
1) What
is the
Length 75 75.025s 75.05 75.075 75.113 75.15 75.225 75.375 75.525 75. 75 76.5
78
79.5
81
81.5
84
87
88.725
(тm)
magnitude of modulus of elasticity?
2) What is the magnitude of Ultimate tensile strength of this alloy.
3) What is the magnitude of The ductility in percent elongation?
Determine the indices for the vectors shown in the following figure:
+2
1) indices for the vectors A
B
A.
2) indices for the vectors B
3) indices for vector c

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Calculation of Question 1

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
A structural member with a rectangular cross section as shown in the accompanying figure is used to support a load of 2500 N. What type of material do you recommend be used to carry the load safely? Base your calculations on the yield strength and a factor of safety of 2.0.
Q5) A specimen of alloy having a rectangular cross section of dimensions 5 mm x 16 mm is deformed in tension. Using the Load (N) Length (mm) tabulated data to plot the engineering stress – strain curve and 75.000 4669.56 75.03 then calculate the following: 8985.96 75.08 12694.14 75.09 (a) Modulus of elasticity. 16264.98 75.14 17991.54 75.18 (b) The yield strength. 19816.2 75.26 22484.52 75.421 (c) The modulus of resilience. 24623.1 75.621 26369.28 75.846 28292.04 77.68
A 20-cm-diameter steel rod is subjected to a tensile load of 1000KN at one end and is fixed at the other end. Calculate the deflection of the rod if it is 150-cm long. (Esteel 200 GPa) PL d = AE where d= end deflection of the bar in meter (m) P= applied load in newton (N) %3D L = length of the bar in meter (m) %3D A = cross-sectional area of the bar in m E = modulus of elasticity of the material (N/m) O 0.73 mm 0.1.51 mm 0.02 mm 0.24 mm
A long rectangular copper bar under a tensile load P hangs from a pin that is supported by two steel posts as shown in figure below. The copper bar has a length of 2.0 m, a rectangular cross section of 20 mm x 200 mm, and a modulus of elasticity Ecu = 100 GPa. Each steel post has a height of 0.5 m, a rectangular cross section of 20 mm x 250 mm, and a modulus of elasticity Es = 200 GPa. Steel post A Copper bar a.) Determine the downward displacement 8 of the lower end of the copper bar with respect to the base support of the steel post at point A due to a load P = 150 kN. (20 marks) b.) What is the maximum permissible load Pmax if the displacement d is limited to 1.0 mm? (5 marks) таз
From Data What is Material Ultimate Strength In Mpa. 1 Material Aluminum 2 Form Cylinder ve 3 Diameter 12.8 mm 4 Gauge Length 5 Tensile Testing 50.8 mm To Failure 7 8 Load (N) Length (mm) 9 0 50.8 10 7330 50.851 11 15100 50.902 12 23100 50.952 13 30400 51.003 14 34400 51.054 15 38400 51.308 16 41300 51.816 17 44800 52.832 18 46200 53.848 19 47300 54.864 20 47500 55.88 21 46100 56.896 22 44800 57.658 23 42600 58.42 24 36400 59.182 25
(Figure 1) Figure 30 mm 140 mm, 30 mm 30 mm 70 mm 30 mm 170 mm 1 of 1 Part A Determine the distance to the centroid C of the beam's cross-sectional area. Express your answer to three significant figures and include the appropriate units. X = Submit Part B Īy = Value μA Submit < Return to Request Answer Compute the moment of inertia Iy about the y' axis. Express your answer to three significant figures and include the appropriate units. Value Request Answer Units ignment Units ? Provide Feedback ?
Suppose that L = 25 mm. (Figure 1) Figure 150 mm 1B y I 150 mm 15 mm A 15 mm 100 mm 1 of 1 > Part A Determine the location y of the centroid C of the beam having the cross-sectional area shown. Express your answer to three significant figures and include the appropriate units. y = Submit Provide Feedback Request Answer P Pearson
A baseline was measured using a 100m tape which is standardized at 15°C with a standard pull of 10kg. The recorded distance was found out to be 430.60 meters. At the time of measurement the temperature was 20°C and the pull exerted was 16 kg. The weight of one cubic cm of steel is 7.86kg and a weight of 2.67kg. Use E = 2x106 kg/cm², a= = 7x10-7/°C a) Compute the cross sectional area of the tape. b) Compute the total correction =) Compute the true length of the baseline
20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 890 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the actual change of volume in final plate. Provide the answer in mm³ a with two decimal points of accuracy. σ = 80 MPa B 8 20 mm Answer: D 20 mm C σ = 160 MPa
In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a clockwise moment of 340 lb in about point A. (Figure 1) Figure A == 18 in. 30° 5 in. 114 1 of 1 Part A Determine the required magnitude of force F. Express your answer with the appropriate units. μÅ F = Submit Value Provide Feedback Request Answer Units ?
Problem #2 The bar shown below has uniform cross section and material properties throughout. In addition to the loads shown, the bar experiences a uniform temperature change of AT = 75.4 °F. Given the x displacement at A is equal to -0.2044 inches determine the magnitude of the external load P. Report your answer in kips to 2 decimal places. D 7.5 ft C 1.7P 4.5 ft B 2.3P 2.5 ft A 3.1P E 29,000 ksi a = 6.5 x 10-6 1/°F A = 0.1 in2