Speed reduction, either through gearing or belt-pulley constructs, is an important element in motion system design. Similarly, converting rotary motion to linear motion is an important consideration. Considering a printer system driven by a stepper motor with 200 steps per revolution, construct a table that shows the relationships for: a. Position resolution of the print head vs. angular position of the motor. This translates to addressable print dots per mm vs. step angle. b. Print head speed (mm/S) vs. motor speed (Steps/S with rpm also noted) C. Frictional load at the print head (mN) vs. reflected torque at the motor (mNM) d. Mass of the print head vs. reflected inertia to the motor Use GR for Speed Reduction, r (mm) for the radius of the drive pulley, and m (grams) for print-head mass.

Speed reduction, either through gearing or belt-pulley constructs, is an important element in motion system design. Similarly, converting rotary motion to linear motion is an important consideration. Considering a printer system driven by a stepper motor with 200 steps per revolution, construct a table that shows the relationships for: a. Position resolution of the print head vs. angular position of the motor. This translates to addressable print dots per mm vs. step angle. b. Print head speed (mm/S) vs. motor speed (Steps/S with rpm also noted) C. Frictional load at the print head (mN) vs. reflected torque at the motor (mNM) d. Mass of the print head vs. reflected inertia to the motor Use GR for Speed Reduction, r (mm) for the radius of the drive pulley, and m (grams) for print-head mass.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A slider-crank mechanism is required to do the following crank angle-slider position coordination. Crank Angle (Q) Slider Position(S) Position-1 0° 12 cm Position-2 90° 10 cm Also at position 2, the speed of the slider will be 5 cm/sec leftwards as the crank is rotating CCW by 1 rad/sec. Then verify your design by drawing your mechanism at crank angles 0° and 90° and measure slider position and see if they are 12 cm 10 cm respectively. If so, proceed with a velocity analysis at second position, assuming that crank has a speed of 1 rad/sec CCW and find the slider speed , check whether it is 5 cm/sec leftwards or not.
01:53 M 1 or Vo LTED :4G + Assignment 1_KoM.pdf 1/2 Kinematics of Machine Assignment 1 1. Describe various inversions of a single slider crank mechanism giving examples. 2. Describe the inversions of double slider crank mechanism with examples. 3. Define mechanical advantage and transmission angle of a mechanism. 4. For the kinematic linkage shown in fig. 1, find the number of binary link, ternary link, quaternary link and degree of freedom. C (1) DE, F Fig. 1(a) Fig. 1(b) 5. What do you mean by degree of freedom of a kinematic pair? How are pair classified? Give suitable examples. 6. In a slider crank mechanism, the length of crank and connecting rod are 100 mm and 400 mm respectively. Locate all the l-centres of the mechanism for the position of the crank when it has turned 45° from the inner dead centre. Find the velocity of slider and point B. 400 mm 45° m mim Fig.2 7. State and prove Kennedy's theorem as applicable to instantaneous centre of rotation. Explain angular velocity…
Problem a. Given joint variables and link parameters, make DH table of RRR robot shown below and calculate T4. (Forward kinematics analysis) b. Given link parameters and coordinates (P calculate 0, 0, and joint angles. (Inverse kinematics analysis) hi 1₁ RRR Robot Ꮎ 12 03 {(P₁.P₁.P.)
I have been working on this Solid Mech problem for a while and have gottem nowhere we are supposed to be finding the modulus of elasticity for a set of data (attached). I have made an excel sheet from this to finda stress strain graph. I understand how the modulus of elasticity is (E = (delta stress)/(delta strain)) but I cannot find the propotional limit that I need to find delta stress and delta strain
Command: PLOTTERMANAGER (from the autocad file m TO CONFIGURE A LOCAL, NONSYSTEM PLOTTER 10. PROFILES-Controls the use of profiles. A profile is a configuration you define. 367N 367N R=1.0m 426N 426N B. 426N C. The two identical sphemes having oqual weights of 367N is placed on top of the three identic al sphere's w/ 426 N as their reight . Compute the reaction A,B and C
The worktable of a numerical control machine tool is driven by a closed-loop positioning system which consists of a servomotor, leadscrew, and optical encoder. The leadscrew has a pitch of 0.25 in/rev and is coupled directly to the motor shaft. The optical encoder generates 200 pulse/rev. The table has been programmed to move a distance of 7.5 in at a feed rate=20 in/min. (a) How many pulses are received by the control system to verify that the table has moved the programmed distance? What are (b) the pulse rate and (c) motor speed that correspond to the specified feed rate?
Problem Statement: A car drives on a circular track with radius 270 m. Initially, the displacement s=0 and the speed is 24 m/s. The car then begins to accelerate at At 0.3s (given in m/s? where s is in meters). After 3.4 seconds has passed, determine: (To get this answer you may need to use a table of integrals and/or a numerical equation solver.) The distance traveled: ûn The velocity vector: un The acceleration vector: Be sure to include units with your answers.
Conventional float actuated device is used as a level measurement sensor, which consist of pulley and a pointer which move over a graduated scale. Let say you are asked to develop a controller-based float actuated system having a sensor for level measurement or may be more than one sensor is required for accurate level measurement, which sensor will you use and why? Draw the whole schematic showing the position of the sensor or sensors. Will pulley be part of your new digital system, if yes justify your answer, if no, then how you will develop a system without using pulley.
Q2. The application glven as In figure A &B can be realized by using an ultra-sonic sensor. Also explain how triangulation method can be used for the same. Using sultable diagrams, explain the process of operation elaborately. Hll semor Oututpu tan s be courted tita) Figure A Soo: SENSOR OUT Figure B
Sketch the 2D figure of cover using AutoCAD and mention all the dimensions 116 5R 90 Dia 12 holes Kid 8R 50 Bia 6R 8R 15R 2 holes 18 Dia 132 Cover
Objective 3: After much debate amongst your coworkers, everyone agrees that the design analyzed in Objective 2 is sufficient to do the job. A coworker attaches a motor to link 2 which rotates it clockwise at 120 rpm at the instant shown in the image. Determine the following using any method you desire. • Velocity of Point B • Velocity of Point C • The angular velocity of Link 4 Make sure you submit all relevant calculations and graphical work in an organized and readable fashion. 4.200 1.800 B 105 0.600 2 LA 3.600
For the following symbolic representation of a robotic manipulator arm: 1. Use the Denavit-Hartenberg (DH) convention to draw the correct coordinate frames on the diagram 2. Define the DH variables and draw them on the diagram 3. Construct and fill a DH table with variables for each joint/link.