Problem 21.16 The bent rod has a mass of 3.4 kg/m. (Figure 1) Figure 0.3 m 1m 0.5 m 1 of 1 Part A Determine the moment of inertia of the rod about the O-a axis. Express your answer to three significant figures and include the appropriate units. Io. = Submit Value Provide Feedback Request Answer Units ?

Problem 21.16 The bent rod has a mass of 3.4 kg/m. (Figure 1) Figure 0.3 m 1m 0.5 m 1 of 1 Part A Determine the moment of inertia of the rod about the O-a axis. Express your answer to three significant figures and include the appropriate units. Io. = Submit Value Provide Feedback Request Answer Units ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.43P

See similar textbooks

Similar questions

For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and y2 = 0.33 m. Find the moment of inertia about the horizontal axis where y=0 (bottom of the cross-section). Report your answer in units of m4 to four decimal places. y y2 x1 2 (no answer) Correct Answer: 0.002021
For problems 1-3, use the following information. A composite shape is drawn to scale below. Grid units are [mm]. 0 1. Determine the area of the shape 2. Determine the moment of inertia about the y-axis. 3. Determine the radius of gyration with respect to the y-axis.
solve using analytical way Given a single disk system that rotates as in picture. If: m₁ = 10 kg; R₁ = 15 cm; 0, 30°, m₂ = 15 kg; R₂ = 20 cm; 0₂ = 100°, m3 = 10 kg; R3 = 10 cm; θ3= 160° dan R₂ = 12,5 cm, calculated "me" and "θe"
In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e angle a at which slider B reaches the extreme right position. Write your answer in degrees but do not write the unit. 7 cm. Find the value of 7777 x. Answer: DELL
Locate all the centros from the 6 bar linkage shown below. Show the centro polygon step by step and name each centro found through the mechanism. Ks = 1 inch : 1 foot Kv 1 inch 16 fps Mechanism 1: Dimension in inches G Tek 2 3 G K 1.0000 1.5000 3.5000 94° G K 2.5000 2 45° 1.0000 3 1.0000 2.0000 - 01.0000
Please show how to solve for #24. The answer is A, but I don't understand how to get there. I have solved for a perpendicular using a = v^2/r and substituting with v = 2 pi r / T. a perpendicular = 50.29 m/s^2, but I am not sure how to solve for a parallel using the equation (a parallel = r * angular acceleration.) Thanks! T = period r = radius a = acceleration
Solve for the indicated value, and graph the situation showing the solution point. The formula for measuring sound intensity in decibels D is defined by the equation D = 10 log (1) using the common (base 10) logarithm where I is the intensity of the sound in watts per square meter and Io = 10-12 is the lowest level of sound that the average person can hear. How many decibels are emitted from a jet plane with a sound intensity of 8.7. 102 watts per square meter? Round your answer to three decimal places. The jet plane emits Number decibels at 8.7. 102 watts per square meter. Select the correct graph of the situation showing the solution point. 200 D 150 100- 50 400 800 1200 1600 2000 400 800 1200 1600 2000 O O 0 200D 150- 100 50 0 200- Subr
Correct: Item B with radius 130mm. Show your COMPLETE solution in 3 decimal places. If W=789 then use it 789. If u dont understand then reject my question ask for information ok
15-1. A 100-ft grid is located over an area that measures 800 ft in the north-south direction and 800 ft in the east-west direction. The southwesterly corner is designated A-1 and the southeasterly corner is designated I-1. The northwesterly corner is designated A-9 and the northeasterly corner is designated I-9. Elevations are obtained at the grid points using a total station instrument, rounded off to the nearest foot. These are tabulated as follows: 375 372 366 360 354 350 340 322 302 312 365 364 8 372 372 370 368 362 361 339 7 366 365 365 366. 362 361 347 319 359 328 328 6. 363 353 350 360 362 350 347 361 340 335 343 352 350 338 334 4 360 344 329 328 337 339 325 321 321 3 360 343 320 317 318 318 313 312 312 308 302 303 323 326 2 358 343 316 310 303 291 340 B 1 353 318 310 303 297 292 A C D F G H Plot a grid to a scale of 1 in. = 200 ft and draw in 10-ft contour lines.
Compute the position and orientation of the tool point P from the given D-H table for the displacement variable e1-90° e2-90° and e3=90⁰ a1= 100 mm, a2= 100mm and a3 = 50mm Note: find the position and orientation using step by step procedure Figure 3 3-DOF (Industrial manipulator arm) Joint 0 d 1 01 0 2 02 3 03 0 0 Present the roll, pitch, yaw and displacement in x, y and z axis. use the composite transformation matrix [ce; -se,Cα; se; SÔ i-¹T₁ = 0 0 Sα₁ 0 CÔ Ca; co,ca; a a1 a2 az s0;Sα; se a | -90 0 0 Cα₁ 0 a;C0₁] –CĐ Sa, : aS0; a¡SO; d; 1
3 0/2points The hand held auger shown uses a driving motor of 2 hp at rotation speed of 2.3 x10 rpm. If it delivers a digging torque of 48 Ib-ft at the rotation speed of 147 rpm. Determine the reaction torque imposed onto the transmission mount. [lb-ft] 20 in (no answer)
For a given non-symmetric area and origin, when plotting Mohr's Circle, a reference point doesn't lie on the circumference but is located at the average distance between Imax and Imin at (297, 0). This reference point is the center of Mohr's Circle must correspond to one of the two principal moments of inertia corresponds to an axis on the cross-section that is not principal O provides the radius of Mohr's Circle that is equal to 297 provides the diameter of Mohr's Circle that is equal to 297