Problem 1 During the isothermal heat addition process of a Carnot cycle, 2000 kJ of heat is added to the working fluid from a source at 500°C. Determine: The entropy change of the working fluid. The entropy change of the source. The total entropy change for the process. Use the answer in part (c) to determine if under the given conditions the process is reversible. Explain why.

Problem 1 During the isothermal heat addition process of a Carnot cycle, 2000 kJ of heat is added to the working fluid from a source at 500°C. Determine: The entropy change of the working fluid. The entropy change of the source. The total entropy change for the process. Use the answer in part (c) to determine if under the given conditions the process is reversible. Explain why.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2 kg of air as an ideal gas undergoes a Carnot refrigeration cycle as shown in the figure. The isothermal expansion occurs at 300K and isothermal compression occurs at 600K. The heat transfer to air during isothermal expansion is 125 kJ. Pressure at the end of isothermal expansion is 75 kPa. | 4 TH 3 1 Determine the entropy change at each step of the cycle. Determine the entropy change during the cycle Indicate which process (if any) is isentropic in this cycle.
A scientist is observing a boiler wherein steam generated at 204.44 F using 11.02 lbs of water a 27°C. The operating pressure is vented to the atmosphere. Determine the change in entropy if the cp of steam is given by: cp = R (3.5+ 1.2T+0.14T²) J/kg-K a. 13.45 BTU/F b. 213.45 BTU/F c. 87.23 kJ/K d. 168.23 kJ/K
A mole of an ideal gas is compressed isothermally but irreversibly at 110 ⁰C from a pressure of 2 bars to 6 bars in a piston-cylinder device. The work needed must be 20% greater than the work of reversible, isothermal compression process. The heat transferred from the gas during compression flows to a heat reservoir at 23 ⁰C. Calculate the entropy changes of the gas, the heat reservoir and total change of entropy.
In a cycle, a 4kg ideal gas(MW=3g/mol and k=2.3) confined in a controlled mass system went through three processes.the gas was started at 20kPa and 310K in the first process, and it was isometrically increased by 30kPa. The gas subject to 400Kusing a process defined by PV^3=C.It returns to its original state polytropically.Calculate the entropy change for each process.
A 50-Kg block of iron casting at 500K is thrown into a large lake that is at a temperature of 285K. The iron block eventually reaches thermal equilibrium with the lake water. Assuming an average specific heat of 0.45 kJ/Kg-K for the iron, the entropy generation during the process is: A. 12.65 kJ/K B. 16.97 kJ/K C. 4.32 kJ/K D. 29.62 kJ/K
Required information Problem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. During the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the working fluid from a source at 400°C. Problem 07.021.b - Entropy change of source in a heat addition process Determine the entropy change of the source. (You must provide an answer before moving on to the next part.) The entropy change of the source is KJ/K.
In a cycle, a 4kg ideal gas (MW=3g/mol and k=2.3) confined in a controlled mass system went through three processes. The gas was started at 20kPa and 310K in the first process, and it was isometrically increased by 30kPa. The gas was subjected to 400K using a process defined by PV^3=C. It returns to its original state polytropically. Calculate the entropy change for each process.
Air goes through a Brayton cycle gas turbine, entering the compressor at 11 °C and 108 kPa. When it reaches the turbine inlet, the air is at 1,061 °C and 1.23 MPa. What is the net change in specific enthalpy of the working fluid after going through the compressor and heat addition processes? You may assume that the specific heat capacity c, is a constant 1.005 --1. kJ-kg 1.K1 throughout the whole cycle. Give your answer in kJ-kg1 to one decimal place.
A 15-kg iron block initially at 250°C is quenched in an insulated tank that contains 80 kg of water at 15°C. Assuming the water that vaporizes during the process condenses back in the tank, determine the total entropy change during this process. 2.18 3.28 04.18 1.38 3.18 5.18
Problem (4.3): 1 kg of air is allowed to expand reversibly in a cylinder behind a piston in such a way that the temperature remains constant at 260°C while the yolume is doubled The piston is then moved in and heat is rejected by the air reversibly at constant pressure until the volume is the same as it was initially. Calculate the net heat flow and the overall change of entropy. Sketch the processes on a (T-S) diagram.
Show the COMPLETE SOLUTIONS including the derivation of formula and interpolations/extrapolations: NO Calculator Technique and Applications. 1. Steam at 228 °C and with a specific entropy of 6.1351. undergoes a poly tropic kg-K process with n=1.81 until the pressure becomes 7.98 MPa (a) what is the final temperature of the stem? (B) What is the work and the process? 2. 5kg of steam has an initial enthalpy of 2711.5 kJ at 0.222 MPa. Isentropic compression gives a final pressure of 0.29 MPa. Find (a) the initial and final temperatures and (b) the work of a steady and nonflow processes?
2. A large slab of concrete, 5 × 8 × 0.3 m, is used as a thermal storage mass in a solar-heated house. If the slab cools overnight from 23 °C to 18 °C in an 18 ° C house, what is the net entropy change associated with this process? at jadi qmuq