Through the following formulas:(100-FGM) DP100-IGMWGI=where:WGI - Wet grain input in ton/hDP-Dryer performance in ton/hFGM - Final grain moisture in %IGM - Initial grain moisture in %EP =WGI-DPwhere:EP - Evaporation power in ton+₂0/hEC = GC HPwhere:EC - Energy consumption in kcal/hGC-gasoil consumption in kg/hHP-heating power of gasoil in kcal/kgSECwhere:SEC - Specific energy consumption in kcal/kgH20Select which of the following specific energyconsumption options correspond to a dryer thathas a performance of 40 tons/h, and is requiredto reduce grain moisture from 17% to 13.5%.Data:ECEP-1000heating power of gasoil-10100 kcal/kggasoil consumption=213 kg/hAnswer500-1000 kcal/kg H201500-2000 kcal/kg H201000-1500 kcal/kg H20OOO

The drying process for grains is a critical operation in agricultural processing, where the aim is…

Select which of the following specific energy consumption options correspond to a dryer that has a performance of 40 tons/h, and is required to reduce grain moisture from 17% to 13.5%. Data: heating power of gasoil=10100 kcal/kg gasoil consumption=213 kg/h

Select which of the following specific energy consumption options correspond to a dryer that has a performance of 40 tons/h, and is required to reduce grain moisture from 17% to 13.5%. Data: heating power of gasoil=10100 kcal/kg gasoil consumption=213 kg/h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

bliuzodt to mopolb 9. If machine parts are degreased by means of kerosene as shown in the diagram, how much kerosene make-up is needed per day? How much kerosene has to enter the degreasing vat per day? There are about 3 lb of grease per 100 lb of machine parts, and 60 tons of machine parts are processed each day. Five thousand pounds of kerosene (the 10% solution) are carried away by the machine parts each day but drip off and are caught and put back in the degreasing vat. Two hundred pounds of the 10% solution are lost each day from the vat by evaporation, spillage, or by being carried away.
Formül; Tmaks T TL Gyab³G' }z5için c = c2 -(1 – 0,630b/a) M-(Izy .z= ly.y) + My(1.z – Izy .y) 4.ly – Izy Oz + dy, tan20, = Му vQ T- It 10 cm Og + dy x- Gy cos20 +Tysin20 , Jort= 2 2 2 600 N X Ly = *% sin20 + Eycos20 , omarsmin = 9s + Oy + , + r 14 cm B Tmaks + rảy Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring at point A. О 56,03 МPа O 53,48 MPa 49,78 MPa O 78,82 MPa 43.37 MPa
1. A steel sphere 3” in diameter heated to 600oF, is to be cooled by immersion in an oil bath at 100oF. Calculate the average temperature of the sphere a) 10 sec and b) 6 min after immersion. For steel, k = 26Btu/ft-h-oF;  = 486lb/ft3 ; Cp = 0.11Btu/lboF.
When The process is accorcing to a law iso thermal. takes place in a perfectly thermally b. C. insulated Cylinder. 8=1.3 Ans.[ 270 i 5.138 1g1.713 1J,52.6i,sSiky.-5.51, 219 5251g, o leg] University of Anbar College of Engineering Mechantont Englning Dpartment Year (Sophomore year) THERMODYNAMICSA Lec. No. Date: / 202 ME2303 Instructor: Asst. Prof. Dr. Saad M. Jalil hr Page Na. Q7 225 1g Ih of air at 4o% enter amixing chamber where it mixes with 540 kg /h of air at isi. Calculate the temperature of the air leaving the Chamber. assuming steady flow conditions. A ssume that the heat loss is negligible . Ans [22.4c] Q8: Aquantity of gas occupying o14n at a pressure of 1.4MNIM? and temperature of 300 č is expanded adiabatirally to 280 K Nimi Cv = 0. 74 Kg 11eg K p=1o41g ng - detennine: a. the mass of gas b. the temperature of the gas after expansion. work done during the expansion. Ans-fa-1.14 kg C. the b. ४३१ C. 180 lT ) Internal mC,(T2-T1) mC,(T2-T
10. A steam drum contains steam having an 86% quality. Assuming that the density of Liquid part is 989kg/m³ and that of the vapor part is 1.23kg/m³, Estimate the specific volume of the steam. (Note: 86% quality indicates the mass in vapor state) Derive with the formula below, show the cancellation, explain the step by step and DRAW a free body diagram/figure. refer with this: PE1 + KE1 + U1 + WF1 + Q1 + W1 = PE2 + KE2 + U2 + WF2 + Q2 + W2 + E losses.
please show work and formulas so that i may learn the process correctly. if you use a table please mention which table was used. thank you so much. 2. Fill in the blank cells of this table: T( C) P(kPa) u(kJ/kg) Phase description 175 2524.5 325 4000 325 Saturated liquid
MECT361 Mechatronics Components and Instrumentation Please solve the problem in keupord 0.Consider the Material Selection Design Problem for the FRAME of a Human Powered Road Vehicle. Define the selection criteria, assign weights (importance), and evaluate the following alternatives based on COST, WEIGHT, STRENGTH, AVAILABILITY, MANUFACTURABILITY, ASSEMBLY, TEST & MAINTENANCE, ENVIRONMENT & SUSTAINABILITY, SAFETY & RELIABILITY: a.Steel b.Aluminum c. Titanium d.Composite- CFRP
What does this graph saw about ice melting at zero degrees Celsius?
Engineering Thermofluids (GENG-1200-1) 6. A boundary layer is: a) A thin layer of fluid (b) A thin layer of fluid in contact with a solid surface that does not move due to fluid viscosity. c) A thin layer of fluid near the solid surface formed by relative motion between the fluid and surface. d) None of the above 7. Cavitation can be avoided by: a) Maintaining the local fluid pressure above the vapor pressure b) Maintaining the local fluid pressure below the vapor pressure (c)) Ensuring that the flow is turbulent. d) Maximizing the temperature of the fluid 8. An oil droplet with a diameter of 250 µm (Micrometer) and surface tension of 0.030 N/m experiences a AP of: a) 240 Pa b) 480 Pa c) 1.2 MPa d) 24 kPa 9. The Bernoulli equation is valid for: a) Steady, inviscid, and incompressible flow b) Compressible and incompressible flow c) Steady, viscous, and incompressible flow d) Steady, inviscid, and compressible flow 10. The fundamental difference between liquids and gases is: a) Liquids…
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of D;, 1 150 mm and wall thickness f; = 20 mm while the outer steel pipe has an inside diameter of D; 2 = 250 mm and wall thickness t, = tị. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k, between the two pipes does not exceed its maximum service temperature of Tp. max = 70°C. The ocean water is at T.0 = -5°C and provides an external convection heat transfer coefficient of h. flowing crude oil is h; = 450 W/m²-K. 0.03 W/m-K) 500 W/m2-K. The convection coefficient associated with the (2) It is proposed to enhance the performance of the…
10.0 mol of argon (monoatomic) gas is introduced to an empty 50-cm^3 container at 20° C. The gas than undergoes an isobaric heating to a temperature of 300° C. a) what is the pressure at which this process happens? b) what is the final volume of gas? c) show this process of a PV diagram. Make sure you include units and properly label axes. d) what is the amount of work done during this process? Is this work done on the gas or by the gas? e) how much he is involved in this process? is the heat going in or out of the system?
= 14 15 16 17 18 19 20 21 22 23 24 25 26 A gas storage cylinder in an ordinary chemical laboratory measures 3.9 cm wide and 16. cm high. This is the label on it. olo Contents: N, gas Pressure: 7.93 atm If the cylinder is opened and the gas allowed to escape into a large empty plastic bag, what will be the final volume of nitrogen gas, including what's collected in the plastic bag and what's left over in the cylinder? Write your answer in liters. Round your answer to 2 significant digits. ?