Parvinbhai Required informationsteadyA bar of steel has the minimum properties Se= 40 kpsi, Sy= 60 kpsi, and Sut= 80 kpsi. The bar is subjected to atorsional stress of 1 kpsi and an alternating bending stress of 22 kpsi. Find the factor of safety guarding against a staticfailure and either the factor of safety guarding against a fatigue failure or the expected ife of the part. For the fatigueanalysis, use1. Modified Goodman criterion2. Gerber criterion3. Morrow criterionTake Ta 0 kpsi and am= 0 kpsl.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.What are the values of the alternating and mean von Mises stresses?The alternating von Mises stress isThe mean von Mises stress is00 kpsi.kpsi.

Answered: Image /qna-images/answer/e108289f-009d-4d6e-a403-5a8cf3a3336b.jpg

Required information steady A bar of steel has the minimum properties Se=40 kpsi, Sy= 60 kpsi, and Sut- 80 kpsi. The bar is subjected to a torsional stress of 1 kpsi and an alternating bending stress of 22 kpsi. Find the factor of safety guarding against a static failure and either the factor of safety guarding against a fatigue failure or the expected fe of the part. For the fatigue analysis, use 1. Modified Goodman criterion 2. Gerber criterion 3. Morrow criterion Take Ta 0 kpsi and Om = 0 kpsi. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What are the values of the alternating and mean von Mises stresses? The alternating von Mises stress is 0 kpsi. The mean von Mises stress is kpsi.

Required information steady A bar of steel has the minimum properties Se=40 kpsi, Sy= 60 kpsi, and Sut- 80 kpsi. The bar is subjected to a torsional stress of 1 kpsi and an alternating bending stress of 22 kpsi. Find the factor of safety guarding against a static failure and either the factor of safety guarding against a fatigue failure or the expected fe of the part. For the fatigue analysis, use 1. Modified Goodman criterion 2. Gerber criterion 3. Morrow criterion Take Ta 0 kpsi and Om = 0 kpsi. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What are the values of the alternating and mean von Mises stresses? The alternating von Mises stress is 0 kpsi. The mean von Mises stress is kpsi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.4P: The strength-to-weight ratio of a structural material is defined as its load-carrying capacity...

See similar textbooks

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, use a characteristic tensile stress obtained from a stress-strain curve as a measure of strength. For instance, either the yield stress or the ultimate stress could be used, depending upon the particular application. Thus, the strength-to-weight ratio RS/Wfor a material in tension is defined as Rs/w= in which a is the characteristic stress and 7 is the weight density. Note that the ratio has units of length. Using the ultimate stress Uas the strength parameter, calculate the strength-to-weight ratio (in units of meters) for each of the following materials: aluminum alloy 606I-T6, Douglas fir (in bending}, nylon. structural steel ASTM-A57.2, and a titanium alloy. Obtain the material properties from Tables [-1 and 1-3 of Appendix I. When a range of values is given in a table, use the average value.
Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~
ou A bar of steel has the minimum properties S,- 276 MPa, S,-413 MPa, and Su= 551 MPa. The bar is subjected to a steady torsional stress (r m) of 103 MPa and an alternating bending stress (oa ) of 172 MPa. Find the factor of safety guarding against a static failure, and either the factor of safety guarding against a fatigue failure or the expected life of the part. For the fatigue analysis use: (a) Modified Goodman criterion. (b) Gerber criterion. (c) ASME-elliptic criterion note // assume the Kr and Ks equal 1
A bar of steel has the minimum properties Se = 276 MPa, Sy = 413 MPa, and Sut = 551 MPa. The bar is subjected to a steady torsional stress of 103 MPa and an alternating bending stress of 172 MPa. Find the factor of safety guarding against a static failure, and either the factor of safety guarding against a fatigue failure or the expected life of the part. For the fatigue analysis use: (a) Modified Goodman criterion. (b) Gerber criterion. (c) ASME-elliptic criterion.
oblem 100 A bar of steel has the minimum properties S₂ = 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is subjected to a steady torsional stress of 15 kpsi with an alternating torsional component of 15 kpsi and an alternating bending stress of 12 kpsi. Find the factor of safety guarding against a static failure, and either the factor of safety guarding against a fatigue failure or the expected life of the part. For the fatigue analysis use: Goodman criterion.