The hand clamp is constructed using a square-threaded screw having a mean diameter of36 mm, a lead of 4 mm, and a coefficient of static friction at the screw of μ = 0.3. To tightenthe screw, a force of F = 20N is applied perpendicular to the handle. Determine the clampingforce in the board AB.50 mmFFAB

The force applied is .The coefficient of friction at the screw is .The mean diameter is .The lead is…

The hand clamp is constructed using a square-threaded screw having a mean diameter of 36 mm, a lead of 4 mm, and a coefficient of static friction at the screw of μs = 0.3. To tighten the screw, a force of F = 20N is applied perpendicular to the handle. Determine the clamping force in the board AB. 50 mm F H A B

The hand clamp is constructed using a square-threaded screw having a mean diameter of 36 mm, a lead of 4 mm, and a coefficient of static friction at the screw of μs = 0.3. To tighten the screw, a force of F = 20N is applied perpendicular to the handle. Determine the clamping force in the board AB. 50 mm F H A B

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.56P: The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The...

See similar textbooks

Similar questions

The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
3. The pulley has a radius of 3". And fits loosely on the 0.5" diameter shaft. If the loadings acting on the belt cause the pulley to rotate with constant angular velocity, determine the frictional force between the shaft and the pulley and compute the coefficient of kinetic friction. The pulley weighs 18lbs 3 in. 5 lb 5.5 lb
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 40 V-pulley is 0.10. The weight of the handle is 2 lb. If a force of 50 lb is applied to the end of the han- dle, determine the maximum torque for which no motion occurs if the torque is applied Counterclockwise. 50 Ib 3 in. +9 in- 18 in.-
The clamp exerts a 145 lb compressive force on the wood blocks. Single-threaded screw BC has lead L = 0.190 in. and mean diameter d = 0.370 in. It turns in the threaded sleeve at C and pushes against B. The coefficient of static friction between the screw threads and the threaded sleeve is = 0.300. Neglect friction at B. 2 in. 2 in. 2 in. B 2.25 in. 2.40 in. 2.25 in. (a) Determine the value of the moment M in ft · Ib to increase the clamping force. (Enter the magnitude.) ft · Ib (b) Determine the value of the moment M in ft · Ib to decrease the clamping force. (Enter the magnitude.) ft · Ib
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 40 V-pulley is 0.10. The weight of the handle is 2 lb. If a force of 50 lb is applied to the end of the han- dle, determine the maximum torque for which no motion occurs if the torque is applied Clockwise. 50 Ib 3 in. +9 in- 18 in.-
Couple forces of F= 35N are applied to the handle of the machinist's vise. The guid at B is smooth. The Single square threaded screw has a mean radius of 6 mm and a lead of 8 mm, and the coefficient of static friction is us=0.27
The 2-Mg lathe with mass center at G is positioned with the aid of the 5° steel wedge. Determine the horizontal force P required to remove the wedge if the coefficient of friction for all contacting surfaces is 0.30. GO A В P\ 5° 900 mm 2300 mm
The three identical rollers are stacked on a horizontal surface as shown. If the coefficient of static friction ugis the same for all pairs of contacting surfaces, find the minimum value of u, for which the rollers will not slip. Answer: Ps=