Q2 is a composite NPN made up of r pieces of Q1 silicon transistors connected in parallel with each other asVBEillustrated. If a voltage VBE is applied, what is the effective Is₂ of Q2 with respect to Isı if Ic₁ = Is₁e V™ ?Ici IciICIIc2 IciIciIciQ1FVBEOIS2 = Is₁e¹○IS2 = Isı ln(r)OIS2 = =- IS1OIS2 = rIsı+Q2 =FVBEIc₁ Ic₁FVBEIc₂

We need to select correct option for given circuit.

Q2 is a composite NPN made up of r pieces of Q1 silicon transistors connected in parallel with each other as VBE Isle VT ? illustrated. If a voltage VBE is applied, what is the effective Is2 of Q2 with respect to Is₁ if Ic₁ Ic₁ Ic2 Ici Ic₁ Ic₁ Ici Ici Ic₁ Q1 F VBE OIS2 = IS1e" OIS2 = Is1 ln(r) 0152 = 151 OIS2 = rIsı F Q2 HK VBE VBE = = Ic2

Q2 is a composite NPN made up of r pieces of Q1 silicon transistors connected in parallel with each other as VBE Isle VT ? illustrated. If a voltage VBE is applied, what is the effective Is2 of Q2 with respect to Is₁ if Ic₁ Ic₁ Ic2 Ici Ic₁ Ic₁ Ici Ici Ic₁ Q1 F VBE OIS2 = IS1e" OIS2 = Is1 ln(r) 0152 = 151 OIS2 = rIsı F Q2 HK VBE VBE = = Ic2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A full-wave bridge rectifier is to be designed to produce a peak output voltage of 10 V, deliver 100 mA to the load, and produce an output with a ripple of not more than 7.5 percent. Assume that the frequency of the source is 50 Hz, and that a constant drop voltage model with Vp = 0.7 V is t of used. D1 D2 vs(1) RL vz(?) D3 D4 Source Rectifier Load a) Calculate the needed value of the load resistor R1. 1 b) Calculate the peak value of the voltage source which should be used V (t). [ c) What will be the value of the ripple voltage V7 [ d) Calculate the value of the required capacitor C. [ e) Explain in your own words the difference between the output with and without using the capacitor in the circuit above.
A hole and electron in close proximity would tend to a. Repel each other b. Attract each other C. Have no effect on each other d. None of the above In a semiconductor, current conduction is due to a. Only holes b. Only free electrons c. Holes and free electrons d. None of the above The battery connections required to reverse bias a pn junction are a. +ve terminal to p and -ve terminal to n b. -ve terminal to p and +ve terminal to n c. -ve terminal to p and -ve terminal to n d. None of the above
Consider a digital logic circuit with two diodes as shown in Figure 1. The diodes, Dị and D2, are ideal (i.e., large signal diode models with V, = 0). 10 D o Vout V2 10 D2 5V 50kn Figure 1 A digital logic circuit with two ideal diodes A. Complete the equivalent circuit below and determine the output voltage vout when vị = v2 = ov. 1Ω D O Vout 12 D2 5V 50k2
Application Problem. A battery pack consisting of n 12V voltage cells connected in par- allel is shown in Figure 1.144. This battery pack is to provide a load current IL of at least 11.5A to the 12 load resistor RL as shown. Assuming that all voltage cells are identical with an open circuit voltage Ei of 12V and an internal resistance Ri of 0.32, calculate the number of cells n needed to provide a minimum of 11.5A to R1; that is, IL 2 11.5A. battery pack + E, E = 12V R= 0.30
For a diode connected NMOS, determine the required drain to source voltage (in V) to produce a drain current of 7.42 μA. Assume the following specifications for the NMOS: k = 8.84 μA/V2, W/L = 2, VTH = 0.7 V, LAMBDA = 0 V-1. Express your answer using 3 decimal places.
In semiconductors to maximnize the the radiative recombination efficiency 14 O a. The non-radiative recombination rate R. should be minimized. O b. T,/t, should be as large as possible. Tar should be very smnall compared to t,. O d. and Tr Tor should be equal. O e. Non of the given choices is correct.
I need the answer as soon as possible
Q2: For the circuit shown in Figure 1: 1. Describe the behaviour of a p-n junction in terms of semiconductor behaviour. 2. Describe and evaluate the circuit. Assume the values for the parameters in the circuit. You should critically evaluate the performance of the circuit and suggest potential applications. o +5V LOAD R VoUT VIN O OV Figure 1: Electronic Circuit for Q2.
QUESTION 2 With the aid of lo-VD graph, briefly describe the behavior of silicon diode and ideal diode in ON state condition. a) b) Figure Q2b represents a voltage regulator circuit. Determine R and V₂ value to maintain V₁ at 10V for a load variation, I, from OmA to 200mA. Then calculate Pzmax for the zener diode. 20V IR R 20 ww Iz Vz Figure Q2b RL
a) Determine the output voltage for all input voltages values. b) Sketch the overall output waveform, Vo(t).
VZENER at D1 is 9.3V with an IZENER of 4mA when active. D2 is a silicon diode and the transistor has a β = ∞ and VBE = 0.7V.What is VA? What is VOUT? What is the power dissipated by the diode D1?
1) It can be accepted that D1 and D2 diodes are from the same family in the circuit given in the figure. a) output voltage, wwwiwwwww wwwww wwwwwwwwwwn w www w 0.33 k2 wwwwww wwwww E 10 V D Si D, Si b) the current flowing through the resistor, ww ww c) currents flowing through the diodes గ wl ww ww calculate. www ww +