Q3: bridge rectifier circuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=x for a reverse bias. The input voltage of the circuit is 240V and 482 load resistance. Determine: The de load current, the power input efficiency and the PIV rating is required for the diodes. D1 Rd=10 D4 RL=480 Vs Vrms Vo D3 D2

Q3: bridge rectifier circuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=x for a reverse bias. The input voltage of the circuit is 240V and 482 load resistance. Determine: The de load current, the power input efficiency and the PIV rating is required for the diodes. D1 Rd=10 D4 RL=480 Vs Vrms Vo D3 D2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(c) Figure Q4(c) illustrates a full-wave bridge rectifier used in ac voltmeter circuit. i) Explain the operation of diode D1, D2, D3 and D4. ii) Calculate the value of resistance R., ac sensitivity and de sensitivity. D1 D2 V=20Vme Rs 03 In=1mA R=2502 D4 R=2502 Figure Q4(c) Full Wave Bridge Rectifier
The four diodes used in a bridge rectifier circuit have forward resistances which may be considered constant at 1 ohm and infinite reverse resistance. The alternating supply voltage is 220 V r.m.s. and load resistance is 580 ohm. Calculate (i) mean load current and (ii) power dissipated in each diode.
S2) Calculate the value range that the load resistance (Ry) must take in order for the zener diode to remain in continuous conduction in the circuit in the figure?
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
I need the answer only those parts. vi,vii,viii,ix,x, Please provide correct solution. And provide **ALL** those parts what i mentioned ( vi,vii,viii,ix,x) WILL UPVOTE YOUR ANSWER IF YOU PROVIDE CORRECT SOLUTION OF VI,VII,VIII,IX,X
* When the peak output voltage is 100 V, the PIV for each diode in a center- tapped full-wave rectifier is (neglecting the diode drop) 200V O 100V 150V 55V If Vi is less than Vz. The Zener diode current is Zero Very low ********** High *< 0.5 A
For the diode circuit shown below, an IN4007 diode is used, and is connected to a variable voltage supply (VIN) that provides a maximum output voltage of 6 V. The 1N4007 diode has absolute maximum forward current rating of 1A, and can be modelled with a diode drop of 0.7 V. What is the minimum value of resistance (R1) you can use to avoid damage to the diode? Answer: Vin ww R1 O Vout
4.) In which mode will a diode generally not conduct electricity? a. Bidirectional Biased b. None of these c. Forward Biased d. Reversed Biased 5.) Consider the following schematic symbol of a semiconductor device: Which side is the Cathode? (Picture inserted down below) a. Side A b. Both side A and B c. Side B d. Neither side A or B 8.) Integrated circuits can be broken down into three basic categories. Which category does an operational amplifier (or op-amp) fall into? a. Analog b. None of these c. A combination of analog and digital d. Digital
Answer a,b,c,d
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izk = 1.5 mA and Vz = 14 V. R 560 0 VIN
For the subsequent questions, consider the half-wave rectifier shown below, with a 60 Hz AC line input AA 2X wt Msmax Vs Vsmax Input Voltage Waveform 3X Select one: O a. OFF, OFF O b. ON, OFF O C. OFF, ON O d. ON, ON 4X 000000000 000000000 In segment (1) the diode is, while in segment (2) the diode is ___ D I VL RL wwwwwww Half-Wave Rectifier -i or VL- (1) VLmax OR Imax (2) X 2X wt Vdc or Idc 3X Rectified output Voltage/Current Waveform 4X www.CircuitsToday.com