14 A0-volt forward voltage is applied to a silicon diode in series with a kond of 3 k2. Drawihe de kud line. What is the slope of the line?Selution The value of voltage Vy across diode is given by Vy v- lR Since R and V arefixed values, this nquation can by represented by a straight line on V-ly characteristics of diode;thn is de kud foe. When I 0, maximum voltage across the diode V 30 V. This is point BC30, 0).10 mA30 VFig. 2.25 Problem 2.4.

In electronics, the p-n junction diode works as the basic building blocks of electronics circuitry.…

14 A 0-volt forwaurd voltage is spplied to a silicon diode in series with a koud of 3 k2. Draw the de kud line What is the slope of the line? Solution The value of voltage Vy across diode is given by Vy V lR Since R and V are fixod values, this equation can by represented by a straight line on V-ly characteristics of diode, ths is de kuad lie. When Iy 0, maximum voltage across the diode V 30 V. This is point DC30, 0). 10 mA 30 V Fig. 2.25 Problem 2.4.

14 A 0-volt forwaurd voltage is spplied to a silicon diode in series with a koud of 3 k2. Draw the de kud line What is the slope of the line? Solution The value of voltage Vy across diode is given by Vy V lR Since R and V are fixod values, this equation can by represented by a straight line on V-ly characteristics of diode, ths is de kuad lie. When Iy 0, maximum voltage across the diode V 30 V. This is point DC30, 0). 10 mA 30 V Fig. 2.25 Problem 2.4.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
A silicon diode with a forward resistance of 100 is connected in series with a 5000 resistor. If an a.c voltage of 20V peak is connected across the series combination of the diode and the resistor what will be the peak value of the current through the diode and the peak output voltage? What will be the peak value of the current through the diode and the peak output voltage if the diode were ideal?
Given the following circuit with VDD= 9.2 V, R=2.3 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. I VDD a. 0.004000 A O b. 3.717391 A OC. 0 A d. 4.000000 A e. 0.003717 A R + VD -
Questions 1 V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 kn. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: None b. 580mA 850mA O c. Od 245mA O e. 425mA D C C: R www Q+ Vo
Since R1=4.51 Kohm, R2=1.19 Kohm R3=2.74Kohm R4=5.60Kohm VCC=23.00V and diode silicon in the circuit given in the figure, find the current passing through the diode in mA
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V