A lead-Acid battery of so cells is to be chargedat 25Aa series2SA from a 200V die supply usingresistor. Ic the emp of each cell is 1.95 V at thecod 2.25v at thethe of thecommencementof chargecharge, find the range of series resistance value ofrequired. The internal resistance of each cell mayconstant at 0.002-2 andleadsbemaybe assumed to remainthe resistance ofignored.the connecting

Answered: Image /qna-images/answer/89bf1567-3f18-424e-80e4-f51386c43fd8.jpg

A lead-Acid battery of so cells is to be charged at a series 2SA from a 200V dic supply using resistor. If the emp of each cell is 1.95 V at the commencement of charge and 2.25v at the of the skies resistance value of charge, find the range of series required. The internal resistance of each cell may constant at 0.002-22 and leads be may be assumed to remain the resistance of ignored. the connecting

A lead-Acid battery of so cells is to be charged at a series 2SA from a 200V dic supply using resistor. If the emp of each cell is 1.95 V at the commencement of charge and 2.25v at the of the skies resistance value of charge, find the range of series required. The internal resistance of each cell may constant at 0.002-22 and leads be may be assumed to remain the resistance of ignored. the connecting

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5. For the circuit in the figure, what should be the value of R2 so that the current passing through the silicon diode (which has Vd= 0.67 Volts) is 250uA
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
VZENER at D1 is 9.3V with an IZENER of 4mA when active. D2 is a silicon diode and the transistor has a β = ∞ and VBE = 0.7V.What is VA? What is VOUT? What is the power dissipated by the diode D1?
Analyze the circuit using KVL or superposition, Analyze the circuit assuming many source values that lead to all possible cases of diode states, re-plot the circuit and develop the relation between the output voltage and the source.
5 For the following circuit: a) Draw a table to mention the names, the states (ON/OFF) and turn on voltages for all the diodes of the circuit. (V = 3.5V for D3) and draw the equivalent circuit. b) Find the voltage across R1, R2, R3 c) Find the current through D1 , Dz , D3 and D4 D1 Si R2 D2 5002 Si R1 7502 R3 D3 D4 V1 1kn Blue GaAs 10v
Q/A - In the bellow circuit, the Zener diode has Vz=20 volt, RL=16 Ohm, the voltage across the load stay at 20 Volt As Iz is maintained between 300mA and 3mA m. Find the value of series resistance R so that Eo remain 20v while input voltage Ei is free to vary between 24Volt to 30Volt. R IL 24-30 Iz Vz Eo wwww. RL
4kN 2V Determine the state of diode for the circuit shown. find ID and VD. Assume simplified model for the diode. (Diode is Silicon). 4k2 2V 1k2. 0.7V O -0.375 mA, 0.4 V, off O -0.67 mA, -0.24 V, on O -1.5 mA, 0.7 v, off O 2.04 mA, -8 V, on
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V omsh RL VI-DC20V 0.01 F 0.02 F 0.0167 F None of the above
What' s the value of the resistor to be connected in parallel of the 6k Ohms resistor to keep/limit the current flowing through the diode 1.5 mA.
Q#2 (a)For Zener diode network determine the VL ,VR ,IZ, and Pzshow in figure #1
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Load resistor RL as shown is 12 kΩ. What are the nominal and worst-case values of Zener diode current and power dissipation if the power supply voltage, Zener breakdown voltage and resistors all have 5 percent tolerances?