(Q2) A pump is driven by an electric motor using an open type flat belt. Determine the width and length of belt for the following data: Power transmission = 15kW Rotational speed of the motor-1,440 rpm Motor pulley diameter = 250 mm Pump pulley diameter 500 mm Coefficient of friction for motor pulley 0.26 Coefficient of friction for pump pulley 0.22 Center distance between the pulleys = 1,200 mm Thickness of the belt 5 mm Density of belt material = 1,000 kg/m? Allowable stress for the belt material = 2 MPa

(Q2) A pump is driven by an electric motor using an open type flat belt. Determine the width and length of belt for the following data: Power transmission = 15kW Rotational speed of the motor-1,440 rpm Motor pulley diameter = 250 mm Pump pulley diameter 500 mm Coefficient of friction for motor pulley 0.26 Coefficient of friction for pump pulley 0.22 Center distance between the pulleys = 1,200 mm Thickness of the belt 5 mm Density of belt material = 1,000 kg/m? Allowable stress for the belt material = 2 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2 / A belt drive consist of two V-belts in parallei, on grooved pulleys of the same size. The angle of the groove is 30". The cross - section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximum safe stress in the material is 7 MN/m. Answer the following questions 1- The centrifugal tension in belts is . . (a) increases power transmitted (b) decreases power transmitted (e) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
The following particulars apply to an inclined belt conveyor: Length of conveyor (loading end to discharge end): 100 mSpeed of belt: 1,5 m/sAngle of wrap around driving pulley: 220 degreesCoefficient of friction between belt and driving pulley: 0,3 Mass of rock conveyed (mass flow rate): 300 t/hThe discharge end is 22 m higher than the loading end. The total friction is equivalent to a force of 6,5 kN in the belt at the head pulley. The efficiency of the drive is 90%. 4.2.1 Calculate the power of the motor. 4.2.2 Calculate the minimum tension in the slack side of the belt as it leaves the driving pulley
Which type of clutch/brake is depicted in the figure below? 10⁰ O A. Internal expanding rim clutch/brake O B. External contracting rim clutch/brake OC. Band-type clutch/brake O D. Axial clutch/brake OE. None of the above
Q1: A simple flat belt drive system shown in the figure has a driving pulley diameter 220mm and runs at 800 r.p.m. clockwise; the diameter of driven pulley is 360mm. The contact angle is 210°. The belt wide is 20mm and 8mm thick. The belt mass per unit length is 0.5 kg/m and the maximum stress in the belt is 8 MN/m. If the coefficient of friction between the belt and pulley is 0.25; take the centrifugal force in to account and determine: 1. Redraw the figure and show (The Tight and Slack sides, tension and centrifugal forces directions at this two sides and the contact angles) 2. The speed of the belt on the driving pulley 3. The tension forces on the belt in the Tight and Slack sides 4. Power transmitted in the system 5. The generated Torque in the dri ing pulley Driven Pulley Driving Pulley
Q1/ An open belt drive connected two pulleys 120 cm and 50 cm diameter on parallel shafts 4 m apart. The belt weights 0.9 kg/m length and maximum tension in it is not to exceed 2000 N. 0.3. The 120 cm pulley, which is the driver, runs at 200 rpm. Due to belt slip on one of the pulleys, the velocity of the driven shaft is only 450 rpm. Calculate the torque on each of the two shafts and power transmitted.
pleassssse solve question 6, statics
Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a distance of 12 m from the driving pulley of 480 cm diameter ?
Q1) A V-belt drive consists of three V-belts in parallel on grooved pulleys of the same size. The angle of groove is 30° and the coefficient of friction 0.12. The cross-sectional area of each belt is 800 mm² and the permissible safe stress in the material is 3 MPa. Calculate the power that can be transmitted between two pulleys 400 mm in diameter rotating at 960 rpm.
Q2/ Two pulleys on parallel shaft are connected by a crossed belt. The diameter of the pulleys is 450 mm and 200 mm. The shafts are 1.95 m apart. Find (a) the length of the belt required, (b) the angle of contact between the belt and each pulley, and (c) the power transmitted by the belt when the larger pulley rotates at 100 rpm, if the maximum permissible tension in the belt is 1000 N and u = 0.25. Q3/ An open belt drive connected two parallel shafts 1.2 m apart. The driving and driven shafts rotate at 350 rpm and 140 rpm respectively and the driven pulley is 40 cm diameter. The belt is 5 mm thick and 8 cm wide. u = 0.3 and maximum permissible stress in the belting is 140 N/cm2. Determine (a) diameter of the driving pulley, (b) maximum power that may be transmitted by the belting, and (c) required initial tension in the belt.
Q2 / A shaft transmitting 15kW at 200r.p.m. are supported by two bearings placed 1 m apart. A 600 mm diameter pulley is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25kN. Another pulley 400 mm diameter is placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt having maximum tension of 3.376kN, which is placed horizontally to the right. The angle of contact for both the pulleys is180° and =0.24. Determine the suitable diameter for a solid shaft if the bending moment acting on the shaft is reversed, allowing working stress of 42MPA in shear for the material of shaft and have yield stress of 400MPA and ultimate stress of 500MP.. And design the keys which support each pulley if the material of the keys is the same for the material of shaft.
Q/The layout of a crossed leather belt drive is shown in Fig. below. The belt, transmits 7.5 kW and operates at a velocity of 13 m/s approximately. The coefficient of friction is 0.3 and the permissible tensile stress for the belt material is 1.75 N/mm2. Calculate (i) The diameters of pulleys; (ii) The length of the belt and (iii) Belt tensions on the tight and slack sides. 500 грm 1000 грm d1 d2 -1500 mm-
(Q2) The following data are given for the drum brake shown in figure (1) • Drum diameter is 400mm • Width of the shoe is 75mm • The coefficient of friction is 0.24 • The maximum pressure is 1MPA. • The drum rotates 3000rpm in counter clock wise direction. • The equivalent polar moment of inertia is 10 kg.m/s? Determine the minimum actuating force and the frictional torque. What is the time required for deceleration to the rest? 62 62 F 100 150° 126 112 50 50 I Fig.(1)