A weight of 200lbs. rests on an inclined plane that makes an angle of 35° with the horizontal. If the coefficient of friction is 0.30, what force must be applied parallel to the plane in order to start uniform motion upward?

A weight of 200lbs. rests on an inclined plane that makes an angle of 35° with the horizontal. If the coefficient of friction is 0.30, what force must be applied parallel to the plane in order to start uniform motion upward?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Related questions

Q: Q2/ Determine the shear stress at points A and B on the beam if it is subjected to a shear force of ...

A: Find the transverse shear stress at point A and B Given data :- Shear force = 400 kN

Q: A steam engine isentropically expands 3 kg/s of steam from 0.86MPA, 2200C. The exhaust is dry and sa...

Q: Find the time required for one full cut on a work piece of 350mm long and 20 mm in diameter. The cu...

Q: the heat to raise the temperature to the melting point the heat to raise the molten metal to the des...

A: Given: density=7.5 g/cm^3 melting point=800 oC specific heat, in solid state 0.33 J/gC in liquid sta...

Q: Find section where maximum bending moment occour ?? Solid mechanics solve fast

A: given:

Q: Draw a sound conclusion based on how you familiarized the key components of the lathe machine. Empha...

A: Lathe stands for Longitudinal Access Turning Horizontal Equipment. In lathe the major operations tha...

Q: D.I 4.5-8. Consider the following problem. Maximize Z = 50x1 + 25x2 + 20x3 + 40x4, subject to 2x1 + ...

Q: 20 kN/m

A: solution of above problem is below:

Q: An advantage of using natural gas, rather than oil, as a fuel is that natural gas is?

Q: he hydroelectric facility that has been proposed will consist of a turbine with an efficiency of 89....

A: Given:Efficicnecy of turbine=η=89.2%=0.892vertical depth of 14.8 m below the riverbedHydraulic diame...

Q: Determine the shear and moment equations throughout the beam. Using these equations, sketch the shea...

A: Draw shear force and bending moment diagram

Q: The above left drawing shows a countershaft with helical gear B, bevel gear D, and two supporting be...

Q: explain the general tips or guidelines for a safe workshop

A: A workshop is defined as a space or structure where work is done, or a seminar or series of meeti...

Q: 5.15 The flow and head requirements for a particular application are 20 cfs and 100 ft., respectivel...

A: Given : Q = 20 cfs = 9000 gpm H = 100 ft N = 1750 rpm To find : Specific speed if connected in serie...

Q: 62.A stone weighs 460 N in air. When submerged in water, it weighs 300N. Find the volume and specifi...

Q: A reversed Carnot cycle has a refrigerating COP of 4. (a) What is the ratio Tmax/Tmin? (b) If the wo...

Q: Consider a regenerative vapor power cycle with two feedwater heaters, a closed one and an open one, ...

Q: width of the blades at the exit is 1 cm. Calculate the following: (a) power required to drive the co...

Q: A solid steel cylinder is enclosed by a hollow copper cylinder; both cylinders are 250 mm long at 20...

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...

A: Given data Upper pressure limit = 35 bar Lower pressure limit = 0.4 bar

Q: 24. The rigid pipe BC shown is supported by a pin at C and an A- 36 guy wire AB (E = 200 GPa). The w...

Q: A two phase liquid - vapor mixture of refridgerant a2 is Contained in a ciosed tank at 10 bar. The q...

Q: A turbine is supplied with 0.6 m³/s of water from a 0.3m diameter pipe; the discharge pipe has a 0.4...

Q: In casting experiments performed during a certain alloy and type of sand mould it took 155 second fo...

A: A cube-shaped casting solidified in 155 seconds in a casting experiment using a specific alloy and k...

Q: cylinder contains a fluid at a gauge pressure of 350kPa. xpress the pressure in terms of the column ...

Q: 65.A cube of wood (s.g. 0.60) has 9-in sides. Compute the magnitude direction of the force required ...

A: Given Specific gravity = 0.9 Side = 9 in = 0.75 ft Fi...

Q: 3.1 Calculate the position of the centroids and the second moment of areas about the horizontal and ...

Q: Three steel plates, each 16 mm thick and width of 300 mm are joined by two 20 mm rivets as shown. As...

A: The tensile stress in the rivet system is calculated by the formula given below as- σt=Pw-dt The Bea...

Q: Perform a literature search and make a timeline for hydraulic machines. Include both hydraulic turbi...

Q: A 55-mm-diameter solid circular shaft as shown in the figure is made up of an aluminum material. The...

Q: Q3/ The overhang beam is subjected to the uniform distributed load having an intensity of w = 40 kN....

Q: A natural feed journal bearing of diameter 60 mm and length 55 mm operating at 25 rev/sec, carries a...

Q: A confined volume of 27 moles an ideal gas (with y 1.42) goes through an expansion process so at the...

Q: Water (3 m/s, 1 cp, 900 kg/m3) flows inside a rectangular duct of sides 3 cm and 2 cm. Calculate th...

A: V=3m/s D=2cm To find Reynolds number

Q: Write down the stress components expression at point A (ox, oy, oz, t xy, t yz, T xz) Show the momen...

A: BENDING COUPLE A couple is said to be bending couple when plane of couple is perpendicular to plane ...

Q: Find vertical and horizontal reaction solid mechanics solve ??

Q: A solid cylinder of circular section of diameter d is of material with specific gravity S This float...

Q: Moment of Inertia rmine the second mor (a) x-axis (b) y-axis

Q: Q4/ If the beam is made from wood having an allowable shear stress t allow = 300 psi, determine the ...

Q: 1. Is it possible to operate a heat engine with only a high-temperature heat reservoir?? 2. Is it po...

A: Second law of thermodynamics is related to entropy change, it states that entropy change of universe...

Q: Determine the maximum w that can be applied if the shear stress limit is 100 MPa. Then determine the...

Q: A square-threaded power screw has a mean diameter, dm = 1.75 in and a pitch, p = 0.875 in. The coeff...

Q: A jet of water 10 cm diameter strikes on a flat plate with a velocity of 18 m/s. The plate is moving...

A: We know that a jet of water with a diameter of 10 cm hits a flat plate at a speed of 18 m/s. We need...

Q: nsing pressure of refigerating sysre 1400 kPa and an evaporating temperature of -20°C. The refrigera...

A: Given: An Ammonia refrigerating system,evaporation temperature ,T1=-20o Cdegree of superheat at exit...

Q: Determine the nodal displacements the forces in each element and the reactions.Use the direct stiffn...

A: GivenE1=30×106PsiE2=15×106PsiA=5in2L2=L1=30in

Q: In a steam power plant, saturated vapor enters the turbine at 7.5 MPa, while having a condenser pre...

Q: Water (3 m/s, 1 cp, 900 kg/m3) flows inside a rectangular duct of sides 3 cm and 2 cm. Calculate the...

Q: Three kg of steam at 121°C and 10% moisture undergoes a constant volume process until the pressure b...

Q: 7. If block A of the pulley system is moving downward at 6 ft/s while block C is moving down at 18 f...

Q: 2. Detemine the elongation of the tapered cylindrical aluminum bar caus the 30-kN axial load. Use E ...

A: P=30kN L=400mm D1=20mm D2=30mm E=72GPa

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
A 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is run three times around a circular post, what is the coefficient of friction between the rope and the post?
(Solution Needed) 1. A block weighing 400 N is pulled along a level from at a constant speed by a rope which makes 40° with respect to the horizontal floor. What is coefficient of sliding friction if the force on the rope is 220 N? (Needs A solution)
If a piece of block weighing 150 kg is to be pulled up by a winch using two cables on a 25 deg inclined plane, find the least force each cable will be subjected to set the block in motion. Assume the coefficient of friction to be 0.25.
3. A rope making 1 % turns around a stationary horizontal drum is used to support a heavy weight. If the coefficient of friction is 0.4. What weight can be supported by exerting a 50 Ib force at the other end of the rope?
Three identical blocks are placed on top of each other on a horizontal plane. Each block has a weight of 110 lb and the coefficient of friction between all surfaces is 0.25. If the upper most block is prevented from moving by a horizontal cable to a vertical wall, find the horizontal force that must be applied at the middle block without causing motion to impend. Pls show full solution with figures.
A 200 lb block is in contact with a plane inclined at 30 degrees to the horizontal. A force P, parallel to and acting up the plane, is applied to the body. If the coefficient of static friction is 0.20, find: a. the value of P to just cause the motion to impend up the plane b. the value of P just to prevent motion down the plane c. the magnitude and direction of the friction force F if P= 80 lbs
A block rest on a horizontal board. the board is gradually tilted upward and theblock just begin to slide when the angle of inclination is 21°. a. Find the coefficient of static friction between the block and the board.
A block rest on a horizontal board. the board is gradually tilted upward and the block just begin to slide when the angle of inclination is 21°, a. Find the coefficient of static friction between the block and the board. b. After the block starts moving it is found that it will keep sliding at constant speed when the angle tilt to 15°. Find the coefficient of kinetic friction. Express in terms of variables the W and other forces.
A bumper jack, used to raise the wheel of an auto- mobile in order to change a tire, is shown in Fig. The mean diameter of the screw is 30 mm, and the pitch of the screw is 6 mm. The coefficient of friction between the screw and the nut is 0.30. Determine the force which must be applied to the crank in order to Raise the automobile. 200 mm 3 kN
A homogeneous ladder 20m long weighing 50 N is leaning against a wall makes an angle of 15 degrees with the wall. Assuming that the coefficient of friction at all contact surfaces is 0.20. What horizontal force (F) acting on the lower third point of the ladder will cause it to slip outward?