Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm.The coefficient of friction between the belt and the pulley is 0.26, angle of lap 160 degree and the max. tension in the belt is 2400 N.

Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm.The coefficient of friction between the belt and the pulley is 0.26, angle of lap 160 degree and the max. tension in the belt is 2400 N.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q/The layout of a crossed leather belt drive is shown in Fig. below. The belt, transmits 7.5 kW and operates at a velocity of 13 m/s approximately. The coefficient of friction is 0.3 and the permissible tensile stress for the belt material is 1.75 N/mm2. Calculate (i) The diameters of pulleys; (ii) The length of the belt and (iii) Belt tensions on the tight and slack sides. 500 грm 1000 грm d1 d2 -1500 mm-
Q3: An open belt drive with (200 and 150 mm) pulleys diameters, and the central distance equal to (0.5 m). The larger pulley speed is (500 r.p.m.), and the coefficient of friction between the belt and the pulley is (0.35). Calculate the power transmitted by the belt drive when the maximum tension on the belt equal to (2200 N).
D B (2 100N AB=10 cm CB=BD=4 cm AF=2cm In the mechanism shown above, the friction coefficient of the sliding limb is given as 0.3. A horizontal force of 100 N is applied from the F point. Calculate the torque required for the AB crank handle to start SYT (Counter Clockwise) motion.
Find the coefficient friction at point A, assume there is no friction at point B.
8. A cross belt arrangement has centre distance between pulleys as 1.5 m. The diameter of bigger and smaller pulleys are 'D' and 'd' respectively. The smaller pulley rotates at 1000 r.p.m. and the bigger pulley at 500 r.p.m. The flat belt is 6 mm thick and transmits 7.5 kW power at belt speed of 13 m/s approximately. The coefficient of belt friction is 0.3 and the density of belt material is 950 kg/m³. If the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of pulleys; 2. Length and width of belt. [Ans. 500 mm, 250 mm ; 4.272 m, 90 mm]
Find the value of frition if coefficient of friction is 0.3 and normal force is 200 N
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
Ql: A box weighing 100 N is at rest on a horizontal floor. The coefficient of the static friction F sin 6 between the box and the floor is 0.4. What is the NA F cos 0 smallest force exerted eastward and upward at an angle of 30° with the horizontal that can start the box in motion?
Vipretion
A cross belt system gives a speed reduction of 6:1 and the centre distance between the pulleys is 2.5 m. The effective radius of the driving pulley is r, = 80 mm and it runs at the speed of 550 rpm. The grove angle of pulleys is 25°. The belt has a mass of 0.35 kg/m and the coefficient of friction of 0.3. If the tension in the belt is not to exceed 650 N, calculate the power that can be transmitted by drive.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.