A belt drive consists of two V-belts in parallel, on grooved pulleys of the same size. The angle of the groove is 30°. The cross-sectional area of each belt is 780 mm2 and the coefficient of friction between the belts and the pulleys is 0,12. The density of the belt material is 1,4 Mg/m3 and the maximum safe stress in the material is 7,5 MN/m2. Consider centrifugal tension. Calculate: 2.1 The mass of the belt per metre length. 2.2 The centrifugal tension (Tc). 2.3The maximum tension (T1). 2.4 Tension on the slack side (T2).

A belt drive consists of two V-belts in parallel, on grooved pulleys of the same size. The angle of the groove is 30°. The cross-sectional area of each belt is 780 mm2 and the coefficient of friction between the belts and the pulleys is 0,12. The density of the belt material is 1,4 Mg/m3 and the maximum safe stress in the material is 7,5 MN/m2. Consider centrifugal tension. Calculate: 2.1 The mass of the belt per metre length. 2.2 The centrifugal tension (Tc). 2.3The maximum tension (T1). 2.4 Tension on the slack side (T2).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/A belt drive consist of two V– belts in parallel, on grooved pulleys of the same size. The angle of the groove is 30°. The cross – section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m³ and the maximum safe stress in the material is 7 MN/m?. Answer the following questions 1- The centrifugal tension in belts is (a) increases power transmitted (b) decreases power transmitted (c) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
A V-belt drive consists of three V-belts in parallel on grooved pulleys of the same size. The angle of groove is 30° and the coefficient of friction 0.12. The cross-sectional area of each belt is 800 mm² and the permissible safe stress in the material is 3 MPa. Calculate the power that can be transmitted between two pulleys 400 mm in diameter rotating at 960 r.p.m.
+ Frictional Forces on Flat Belts When engineers design belt drives and band brakes, they engineer them to withstand the frictional forces that develop between the belts or bands and their contacting surfaces. These frictional forces lead to tensions on each side of the contacting surfaces that are unequal; the segment aligning with the motion of the belt or band has a greater tension. Figure B 0.500 m 0.200 m -0.400 m- A 3 of 3 0.300 m Part C mc= Block A has a mass of mA = 49.0 kg and rests on a flat surface. (Figure 3)The coefficient of static friction between the block and the surface is A = 0.300. The coefficient of static friction between the rope and the fixed peg B is 0.320. The width of the block is d = 0.250 m. Find the greatest mass, mc, that weight C can have such that block A does not move. Express your answer numerically in kilograms to three significant figures. ▸ View Available Hint(s) Submit Drouide Foodbook VAZO I vec ? 1 of 3 kg > Review
Friction belt quiz Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
(Q2) A pump is driven by an electric motor using an open type flat belt. Determine the width and length of belt for the following data: Power transmission = 15kW Rotational speed of the motor=1,440 rpm Motor pulley diameter = 250 mm Pump pulley diameter = 500 mm Coefficient of friction for motor pulley = 0.26 Coefficient of friction for pump pulley 0.22 Center distance between the pulleys = 1,200 mm Thickness of the belt = 5 mm Density of belt material = 1,000 kg/m? Allowable stress for the belt material = 2 MPa
Question 4 Squared & ground end A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (16)
In an open flat belt drive, a pulley of 800 mm diameter runs at 300 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, the angle of lap is 170° and the maximum tension in the belt is 2000 N. The power transmitted is: 10.5 kW 9.4 kW 8.9 kW 7.6 kW None of the mentioned 13.1 kW
The width of the belt used if its thickness is 6 mm. Ans. 261 mm 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt speed of 25 m/s. The belt has a mass of 2 kg/m of the belt length. The belt is used in a crossed configuration to connect a 300 mm diameter driving pulley to a 900 mm diameter driven pulley at a shaft spacing of 6 m. A. Calculate the belt length and the angles of wrap. Ans. 13.95 m, 3.34 rad or 191.4° B. Compute the belt tensions based on a coefficient of friction of 0.33. Ans. 1.76 KN, 1.96 KN
Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
Determine the percentage increase in power capacity made possible in changing over from flat belt drive to V-belt drive. The diameter of pulley is same as the pitch diameter of grooved pulley. The pulley rotates at the same speed as the grooved pulley. The coefficient friction for the grooved and flat belt is same and is 0.3. The V-belt pulley groove angle is 60°. The belts are of the same material and have same cross-sectional area. In each case, The angle of warp is 150°.
An overhung cast iron pulley transmits 7.5 kW at 400 r.p.m. The belt drive is vertical and the angle of wrap may be taken as 180°. Find: (a) Diameter of the pulley. The density of cast iron is 7200 kg/m3. (b) Width of the belt, if the coefficient of friction between the belt and the pulley is 0.25. (c) Diameter of the shaft, if the distance of the pulley centre line from the nearest bearing is 300 mm (d) Dimensions of the key for securing the pulley on to the shaft. (e) Size of the arms six in number. The section of the arms may be taken as elliptical, the major axis being twice the minor axis. The following stresses may be taken for design purposes: Shaft and key: Tension – 80 MPa Shear – 50 MPa : Tension – 2.5 MPa : Tension – 4.5 MPa : Tension – 15 MPa Belt Pulley rim Pulley arms