Q4) A multi-disc clutch is constituted of 8 discs, the outer diameter of the contact surface is 150 mm and the inner diameter is 110 mm. Find the total load on the spring with which the disc will be held together if 6 KW is to be transmitted at 1000 rpm assuming the coefficient of friction equal to 0.08 then what is the load carried by each effective contact surface? Answer: The total load on the spring = 11000 N& The load carried by each surface = 785 N %3D

Q4) A multi-disc clutch is constituted of 8 discs, the outer diameter of the contact surface is 150 mm and the inner diameter is 110 mm. Find the total load on the spring with which the disc will be held together if 6 KW is to be transmitted at 1000 rpm assuming the coefficient of friction equal to 0.08 then what is the load carried by each effective contact surface? Answer: The total load on the spring = 11000 N& The load carried by each surface = 785 N %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
The multiple vee-belt drive illustrated in Figure Q5(b), has a groove angle of 40° and is required to transmit 17.4 kW from a pulley 165 mm in diameter to another pulley 330 mm in diameter which rotates at 390 rev/min. The coefficient of friction between the belt and the pulleys is 0.32 and the maximum permissible belt tension is 550 N for each of the five belts used. For this geometry and conditions, calculate: i) the torque on the smaller pulley; ii) the angle of lap (0s) required to achieve this power rating; iii) the ideal centre distance (C) for this angle of lap.
Q1/ An open belt drive connected two pulleys 120 cm and 50 cm diameter on parallel shafts 4 m apart. The belt weights 0.9 kg/m length and maximum tension in it is not to exceed 2000 N. 0.3. The 120 cm pulley, which is the driver, runs at 200 rpm. Due to belt slip on one of the pulleys, the velocity of the driven shaft is only 450 rpm. Calculate the torque on each of the two shafts and power transmitted.
5. Arough rule for leather belt is that effective tension in it, shall not exceed 15 N/mm of width for a belt of 10 mm thickness. This rule is applied to determine width of belt required to transmit 37 kW, under the following conditions : Angle of lap = 165°; Coefficient of friction = 0.3; Velocity of belt = 1500 m/min; Density of leather = 950 kg/m³. Find the width of belt required. Assuming limiting friction between belt and pulley rim, find the stress in the belt. [Ans. 140 mm ; 1.48 MPa]
A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take μ = 0.42. Assume uniform wear in clutch.
The tensions in the tight and slack side of a belt drive system are 1850 N and 525 respectively. If the belt speed is 8 m/s what power in kW will be transmitted with no slippage
Find the power capacity and the cone angle of a cone clutch under uniform pressure having 220 mm major diameter, 180 mm minor diameter, length of contact of 120 mm, 880 rpm,and allowable pressure of 80 kPa.
An multi axial plate clutch used in injection molding machine consist of a three pairs of contact surfaces for engaging and disengaging power from the engine. The engine used for power has a maximum torque capacity of 120 N-m and is transmitted to machine without losses. The permissible intensity of pressure is 350 kPa and the coefficient of friction is 0.35 for the clutch system used in the machine. It was determined that the machine will operate on maximum capacity of torque if the ratio of inner diameter to outside diameter of the axial clutch is 0.577. Assuming uniform wear theory, calculate the inner and outer diameters of the friction lining.
2- A multiple disc clutch has three discs on the driving shaft and two on the driven shaft , providing four pairs of contact surface. The outer diameter of the contact surface is 25 cm and the inner diameter is 15 cm . Determine the Max. axial intensity of pressure between the discs for transmitting 25 h.p power at 500 r.p.m. Assuming uniform wear and coefficient of friction as 0.3 The orial Pressure being limited to
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.