Q2 A power station is to supply two loads. The daily load curves of two loads areshown in figures below:MWMW252520201515101012162024 hours121624 hoursLoad curve ALoad curve B1- Plot the load and duration curves of power station.2- Find:i-Load factor of each load.Load factor and Diversity factor of power station.iii- The reserve capacity and Capacity factor of the power station .If thepower station consists of three units, the installed capacity of eachunit is 20 MW.11-

As per bartleby expert policy, only three subparts are to be answered. Kindly repost remaining…

Q2 A power station is to supply two loads. The daily load curves of two loads are shown in figures below : MW MW 25 25 20 20 15 15 10 10 12 16 20 24 hours 12 16 24 hours Load curve A Load curve B 1- Plot the load and duration curves of power station . 2 Find: i- Load factor and Diversity factor of power station. Load factor of each load. 11-

Q2 A power station is to supply two loads. The daily load curves of two loads are shown in figures below : MW MW 25 25 20 20 15 15 10 10 12 16 20 24 hours 12 16 24 hours Load curve A Load curve B 1- Plot the load and duration curves of power station . 2 Find: i- Load factor and Diversity factor of power station. Load factor of each load. 11-

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.
A single phase 120V AC sourc controls power to a resistve load 20N using integral cycle control. a) Find the output power for both output voltage waveforms shown below. b) The voltage and the current ratings of the switch. c) The duty cycle and the value of TON to produce 0.63KW power. d) The power factor for part (c). Awww TON -TON
The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.
Q20. The section bus-bars A and B as shown in Figure B5 are linked by a bus-bar reactors each rated at 5000 kVA with 10% reactance. On bus-bar A, there are two generators each of 10,000 kVA with 10% reactance and on B two generators each of 8000 kVA with 12 % reactance. Find the Current and MVA that fed into a dead short circuit between all phases on B with bus-bar reactor in the circuit. Page 4 of 5 جامعة التقنية والعلومر التطبيقية بإبراء University of Technology and Applied Sciences - Ibra Student ID: Section: Student Name: 8,000 kVA 12% 10,000 kVA 10,000 kVA 10% 8,000 kVA 12% 10% 2 3 5,000 kVA 10% lell 8,000 kVA 10% Figure B5 "End of Question Paper"
Unit commitment if the spinnind reserve not there in the power system what will happen?
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
The indication of a lagged demand meter approaches the value of the actual load at a rate which is proportional to A. Quotient of the load and the meter indication. B. product of the load and the meter indication C. Difference between the load and the meter indication D. sum of the load and the meter indication
Draw the circuit diagram of Two quadrant chopper which is having average load voltage might be positive or negative. Explain each quadrant operation with neat sketch. I want more than 350 words and I do not want it in handwriting
Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
A generating station is to supply four regions of load whose peak loads are10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Then the installed capacity is (25 to26)MW. O (24 to25)MW. O (23 to24)MW. O
In a PWM, how do we calculate duty cycle?