7. A power station has to meet the following load demand: 50 kW Load A between 10 A.M. and 6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (1) diversity factor (ii) units generated per day (äi) load factor. K) 1-43 G) 880 kWh (ii) 52-38%

7. A power station has to meet the following load demand: 50 kW Load A between 10 A.M. and 6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (1) diversity factor (ii) units generated per day (äi) load factor. K) 1-43 G) 880 kWh (ii) 52-38%

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

A generating station is to supply four regions of load whose peak loads are10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Then the installed capacity is (25 to26)MW. O (24 to25)MW. O (23 to24)MW. O
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.
What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
The indication of a lagged demand meter approaches the value of the actual load at a rate which is proportional to A. Quotient of the load and the meter indication. B. product of the load and the meter indication C. Difference between the load and the meter indication D. sum of the load and the meter indication
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
The peak load on a 50 MW power station is 39 MW. It supplies power through for transformers whose connected loads are 17, 12,9 and 10 MW. The maximum demands on these transformers are 15, 10, 8 and 9 MW respectively. The annual load factor is 50% and the plant is operating for 65% of the period in a year. 102. The average load on the station is (A) 50000 kW (C) 39000 kW (B) 19500 kW (D) 48000 kW. 103. The energy supplied per year is (A) 438 x 106 kWh (C) 170.82 x 106 kWh (B) 341.64 x 106 kWh (D) 420.48 x 106 kWh.
An alternator with internal vallage of 125, p.u. and synchronous reactance of 0.4 p.u. is connected by a transmission line of reactance 0.1 p.u. c a synchronous meto having synchronous reactance 2.35 p u. and internal voltage of 0.85/6, p.u. If the real power supplied by the alternator is D 806 p... than (8, & is. degrees. (Round off to 2 decimal places) (Machines are of non-salient typa. Naglact resistances)
5. Draw the daily load curve and load duration curve for a power station with any arbitrary loads you like. From the load curve, determine the following. i. Maximum demand ii. Average demand ii. Daily energy consumption
2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
7. A power station has to meet the following load demand: Load A 50 kW between 10 A.M. and6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (i) diversity factor (ii) units generated per day (iii) load factor. () 1-43 (ii) 880 kWh (iii) 52-38%]
Draw the circuit diagram of Two quadrant chopper which is having average load voltage might be positive or negative. Explain each quadrant operation with neat sketch. I want more than 350 words and I do not want it in handwriting
A 3-phase star connected, 1500 kVA, 13 kV alternator has an armature resistance of 0.9 ohm and a synchronous reactance of 8.0 ohms. When carrying rated load voltage, calculate the generated voltage per phase at loads of I.) Unity P.F. ii.) 0.8 lagging P.F. iii.) 0.8 leading P.F. iv.) calculate the voltage regulation for each load and determine best regulation.