Problem 5Compute the power delivered to the load by the three-phase generator in the circuit shownin the following figure2 |PageanRjine aww-ÖZ,ab Rline b'Vcbc Rline c'RneutralSchematics, Diagrams, Circuits, and Given Data: V,V ôn = 480Z(-27n /3) V; Ven = 480Z(27/3) V; Z, = 2+ j4 = 4.47Z1.107 N;Rjine = 2 2; Rneutral = 10 2.an = 48020 V:

Problem 5 Compute the power delivered to the load by the three-phase generator in the circuit shown in the following figure 2 |Page an Rjine a wwÖZ, a b Rline b' Vcb c Rine c' wWOZ, Rneutral Schematics, Diagrams, Circuits, and Given Data: V, Vbn = 4802(-27n /3) V; Ven = 480Z(2r/3) V; Z, = 2+ j4 = 4.47Z1.107 N; Rjine = 2 2; Rneutral = 10 2. an = 48020 V:

Problem 5 Compute the power delivered to the load by the three-phase generator in the circuit shown in the following figure 2 |Page an Rjine a wwÖZ, a b Rline b' Vcb c Rine c' wWOZ, Rneutral Schematics, Diagrams, Circuits, and Given Data: V, Vbn = 4802(-27n /3) V; Ven = 480Z(2r/3) V; Z, = 2+ j4 = 4.47Z1.107 N; Rjine = 2 2; Rneutral = 10 2. an = 48020 V:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Similar questions

Explain current divider rule in ac circuits with two parallel impedances Z1 and Z2. Calculate the currents I1 and I2 in phasor form for the circuit given in figure.
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
Impedances Z2 and Z3 in parallel are in series with impedance Z1 across a 100 V, 50 Hz ac supply. Z1 =6.25 + j1.25 ohm; Z2 = 5+ j0 ohm and Z3 = 5-jXc ohm. Determine the value of capacitance of Xc such that the total curent of the circuit will be in phase with the total voltage. When is then the circuit current and power.
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
= = Impedances Z₂ and z3 in parallel are in series with an impedance z₁ across a 100V,50Hz AC supply. Z₁ (6.25 +j1.25)ohms, Z₂ = (5 + j0)ohms and Z3 (5 - jxc)ohms. Determine the value of capacitance Xc said that the total current of the circuit will be in phase with the total voltage. What is then the circuit current and power?
Sketch the phasor diagram of the above circuit in terms of impedance, voltage, and the power triangle.
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
In the 3-phase circuit in the figure, f = 2000 Hz. Find line and phase voltages and currents for the load.(in amplitude and phase).
In general, a three-phase induction motor isdesigned for wye connection operation. However, forshort-time operation, a delta connection can be used atthe nominal wye voltage. Find the ratio between thepower delivered to the same motor in the wye anddelta connections.
The phase b voltage and the phase b current of a balance three-phase system are V = 220 sin (wt + 210°) and I = 10 sin (wt-180°). * A. 5256.44 W B. 5514.38 W C. 5715.76 W D. 6049.22 W
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZRY = 50 +j50 Q , ZYB = 150 + j0 Q and ZBR= 50 – j50 N. (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.