Q-2: Estimate short-term and long-term deflections for simply supported beam shown in Figure below, which is assumed to be made of nominal aggregates and properties removed at twenty-eight day. Concrete grade: C30 Instantaneous static modulus of elasticity = 26 kN/mm² Reinforced: hot-rolled high-vield f 160 2

Q-2: Estimate short-term and long-term deflections for simply supported beam shown in Figure below, which is assumed to be made of nominal aggregates and properties removed at twenty-eight day. Concrete grade: C30 Instantaneous static modulus of elasticity = 26 kN/mm² Reinforced: hot-rolled high-vield f 160 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. From the figure shown, fc' = 20 MPa, fs = 140 MPa, and n = 12. Determine the moment capacity of concrete and steel (Cracked Analysis Only) 750mm IDOM 40bmm 2-32 mm (Gomm Ssomm 2uo mm
Q-2: Estimate short-term and long-term deflections for simply supported beam shown in Figure below, which is assumed to be made of nominal aggregates and properties removed at twenty-eight day. Concrete grade: C30 Instantaneous static modulus of elasticity = 26 kN/mm² Reinforced: hot-rolled high-yield fy = 460 kN/mm² = 10 kN/m u.d.l = 5 kN/m u.d.l Loading: dead (permanent Live (transitory) h=700 b=300 AS 009 =P 2 No 12mm bars span=12m 5 No 25 mm bars
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
The composite bar consists of a 25-mm-diameter A-36 steel segment AB and 60-mm-diameter red brass C83400 end segments DA and CB. (Figure 1) Figure -250 mm- D A 500 mm 75 kN 75 kN 100 KN 100 KN B 1 of 1 > 250 mm- C Part A Determine the average normal stress in segment DA due to the applied load. Express your answer to three significant figures and include the appropriate units. ODA = Submit Part B JAB = O Submit HÅ Value Request Answer Determine the average normal stress in segment AB due to the applied load. Express your answer to three significant figures and include the appropriate units. μA Value C Request Answer Units ? Units ?
A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
The modulus of elasticity of "reinforced concrete" in RC design, is O A. 420 GPa B. 200 GPa C. None () D. 220 GPa
Problem 1: Transformed Moment of Inertia and Elastic Deflection Given: The center of the top and bottom rebars are placed 2.5" from the top and bottom faces. Top Reinforcement: 2 no. 4 Rebar Bottom Reinforcement: 4 no. 9 Rebar Use textbook table A-1 for rebar properties Es = 29,000 ksi Ec = 3,600 ksi Unit weight of plain concrete = 145 lb/ft³ a. Find the transformed moment of inertia of the composite section. b. Calculate the reinforcement ratio p where p is Asb/bd. Asb is the area of the bottom steel, d is the depth from the top face of the beam to the bottom steel, and b is width of the beam. 16" c. A 30' simply supported beam has this cross-section. Ignoring the effects of cracking, how much would the beam deflect under its own self-weight and a live load of 0.64 kip/ft? d. Often the unit weight for reinforced concrete is assumed to be 150 lb/ft³. Repeat part c. using this assumption. e. Repeat part c. using the gross moment of inertia. Note: the gross moment of inertia is the…
ASAP DONT REJECT ME, I'LL GIVE UPVOTE THANK YOUU Solve the basic development lengths in tension for the following deformed bars embedded in normal-weight concrete. State if you have assumptions. (a) 12mm bar dia; 32 mm bar dia. fy = 41.4 MPa fy = 413.7 MPa (b) 44mm bar dia; 57 mm bar dia. f c = 28 MPa fy = 552 MPa
The cross section of a beam is shown in the figure is reinforced with 5-28 mm diameter bars placed at 100 mm from the bottom fiber. The beam is expected to carry a service moment of 280 kN-m. Use f'c=28 MPA and fy=280 MPa. All dimensions are in millimeters. Using WSD method, calculate the following: 1. Cracking moment of the section. 2 Compressive stress on the concrete., 3. Tensile stress on the steel. 4. Compressive force on the concrete. 300 I00 300 300 300 100 mm 100 -1700 mm
Q2: A cold drawn steel rod of circular cross- section is subjected to a variable bending momen of 565 N.m to 1130 N-m as the axial load varies from 4500 N to 13 500 N. Determine the required diameter of the rod for a factor of safety 2. Neglect any stress concentration and column effect. Assume the following values: Ultimate strength = 550 MPa Yield strength = 470 MPa Size factor = 0.85 %3D Surface finish factor = 0.89 Correction factors = 1.0 for bending = 0.7 for axial load The endurance limit in reversed bending may be taken as one-half the ultimate strength.
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION,20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE XDIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF AUNIFORMLY DISTRIBUTED FORCE OF Px=3kN (COMPRESSION), Py=4kN(TENSION) AND Pz=7kN (COMPRESSION) IN THE X, Y AND Z DIRECTIONSRESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa,DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSODETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THEWOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
2. A uniform concrete slab is to be attached to two rods whose lowers ends are initially at the same level. What is the required area, in mm?, of aluminum rod so that slab will remain level after it is attached to the rods? Wi4 m Aluminum E = 72 GPa Steel A= 8V mm 2 E = 200 GPa WI4 m -Y/40 m- Y/200 m