The cross section of a beam is shown in the figure isreinforced with 5-28 mm diameter bars placed at100 mm from the bottom fiber. The beam isexpected to carry a service moment of 280 kN-m.Use f'c=28 MPA and fy=280 MPa. All dimensions arein millimeters. Using WSD method, calculate thefollowing:1. Cracking moment of the section.2 Compressive stress on the concrete.,3. Tensile stress on the steel.4. Compressive force on the concrete.300I00300300300100 mm100-1700mm

The basis of this method is that the permissible stress for concrete and steel will not be exceed…

Answered: 1. Cracking moment of the section. 2.…

Engineering

Civil Engineering

1. Cracking moment of the section. 2. Compressive stress on the concrete. 3. Tensile stress on the steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assuming concrete is uncracked. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1x10°kg cm . Determine the cracking moment of the section. A = 10cm² %3D E, = 2*10°kg / cm² E = 2*10°kg / cm² %3D %3D f'. =1836kg / cm² %3D 90 cm 100 cm 40 cm
A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A concrete beam reinforced for tension has a section shown. The rebars are laid out in a single layer only. The compressive strength of concrete is 24 MPa and yield strength of steel bars is 345 MPa. b= 300 mm h=740mm sc=60mm As = 5 pieces of 36 mm diameter rebars 1. Calculate the depth of compression block in mm 2. Calculate the depth of neutral axis c in mm 3. Type failure (Tension, Compression, Transition) 4. Calculate the actual tensile stress in the tension reinforcements in MPa 5. Calculate the Ultimate Moment Capacity of the beam in kN-m b As SC
A rectangular reinforced concrete beam with width of 250 mm and effective depth of 500 mm is subjected to 150 kN-m bending moment. The beam is reinforced with 4-25 mm o bars. Use alternate design method and modular ratio n = 9. 1. What is the maximum stress of concrete? 2. What is the maximum stress of steel? 3. What is the total compressive force in concrete? b = 250 009=P -0000- b = 250 d-x nA. 4-25 mm Ø ΝΑ
Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300
The concrete at the top of the cross section shown in Figure 4 is formed in a triangle. Calculate the flexural strength, Mn, for the cross scction. The centroid of a triangle is shown for your reference. Assume f. = 4, 000 psi %3D
A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
A beam carrying an allowable actual moment of -38 KN- m is reinforced as shown. If the the concrete is normal weight and f'c = 25MPa and fy = 420MPa. Determine the following: a. The cracking moment of the beam. b. The transformed moment of Inertia. c. The actual tension steel stress. d. Check the stress if it is correct by force checks. mm www.009 4-020 О 140 mm 300 mm 170 mm * 170 mm: ww.08 ✓ 60 mm
1. A steel section of length L sits on an 8" x 8" bearing plate. The bearing plate is perfectly rigid and sits on a 15 in x 15 in x 4 foot high concrete block which is fixed at the base. The system supports an axial load of P. A. Determine the normal stress in the steel. B. Determine the normal stress in the concrete. C. How much did the entire system shorten (Hint: the plate is perfectly rigid so it does not deform-just pretend it isn't there.) 15 in. Concrete 4 ft. 15 in. 8 in. Top View 8 in. Given: P = 250 kips L = 12 ft. d₁= 1 in. d₂ = 4 in. Esteel = 30,000 ksi Econcrete = 4,000 ksi
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly