Civil PProblem 21: A rod is composed of three segments and carries the axial loads as shown. Determinethe stress in each materialIndicate if C or T. The properties of each segment are givenbelow:Bronze120 KNAluminum Steel50 kNL (mm) A (mm²) E(GPa)600 240083120070600200BronzeAluminum 400Steel 300

Stress is defined as internal resisting force per unit area of the cross section. In the given…

Problem 21: A rod is composed of three segments and carries the axial loads as shown. Determine the stress in each material below: Bronze 120 KN Aluminum Steel 50 kN Indicate if C or T. The properties of each segment are given Bronze Aluminum Steel L (mm) A (mm²) E (GPa) 600 2400 83 400 1200 70 300 600 200

Problem 21: A rod is composed of three segments and carries the axial loads as shown. Determine the stress in each material below: Bronze 120 KN Aluminum Steel 50 kN Indicate if C or T. The properties of each segment are given Bronze Aluminum Steel L (mm) A (mm²) E (GPa) 600 2400 83 400 1200 70 300 600 200

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
(1) Given A992 steel Ag = 10 in %3D KLy- 80, ry what is $ Pa=? = 60 the' column streugth design
15 kip Specific Weight y Elasticity E Rigidity G (Ib/in") Modulus of Modulus of Yield Strength (ksi) Materials (10) ksi (10) ksi Tens. Comp. Shear A - Structural A36 - Stainless 304 - Tool L2 0.284 29.0 11.0 36 36 Steel 0.284 28.0 11.0 30 30 Alloys 0.295 29.0 11.0 102 102 2 ft 4 kip 4 kip The A-36 steel bar shown in the figure is made from two segment shaving cros OSS- B sectional areas of AAB-lin^2 and ABD=2in^2. Determine the vertical displacement of end A and the displacement of B relative to C. 1.5 ft 8 kip 8 kip| C 1 ft D
sinav.gelisim.edu.tr/ExamUser/Take?examSessionld The yield imit for a typE of steel material is determined to k3600 keran. Detemine the permissible (allowable> tensile sress for this material acxording to S64S. (o r=) D 2,16 ton/cm² 23.60 ton /cm² 2 2,04 ton /cm² 1,44 ton /cm2 DBoş bırak Карat
(40 How A Rismatic steel bar of a Square cro ss section (looxlo0)mm is loaoled by Compressive force P= 1300 K, the bar has length 2.5 m, Eg=200GPay V=0.3,determine the shortening 8, the increase in the dimensions of cross Section, the change in Volume DV of the bar? loomm loomm
Q2\ A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. A (mm') E (GPa) Ow (MPa) =TTT Aluminum Bronze 450 83 120 3P Bronze Steel 2P P AP- Aluminum 600 70 80 Steel -0.6 m→l- - 1.0 m- H-08 m- 300 200 140
A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which is 699.93mm long. If the weight of the beam is 375KN, determine the stress in the aluminum bar in MPa. (Round your answer to 3 decimal places) (Exclude your unit in the answer box) Bronze Alum 850 1500 Ain mm E in GPa 70 83 bronz alum bronze
1. The hanger assembly shown supports a 4500-kg pipe. The working stresses for each of the hanger assembly components are as follows: Tensile Stress in the Hanger Rod ≤ 140 MPa Shearing Stress in the bolt ≤80 MPa Bearing Stress between the bolt & the Bottom Strap ≤ 120 MPa Calculate the following: a. Required diameter of the hanger b. Required diameter of the bolt
2- the rubber blocks shown in Figure 2 are used in a double U shear mount component. The dimensions of the rubber blocks are 15 x 21 x 25 mm and the applied load of 650 N cause the upper frame to be deflected by 5 mm. ↓ Double U anti-vibration shear mount 15 Shear deformation of blocks 25 Rubber block dimensions 21 오 Figure 2 (a) determine the average shear stress and shear strain in each of rubber blocks (b) determine the shear modulus G of the rubber material used in this component.
A 6m long solid bar of circle section has 140mm diameter for aluminum for length of 4m, while it has 120mm diameter for a length of 2m for steel bar, as shown in figure. Find the elongation of the bar, when it is subjected to an axial tensile force of 300 kN. Take Est-200GPa, Eal- 70 GPa. (30 marks) 140 I *** 300 Kn Aluminum (30 marks) 4 m Steel 2 m 300 Kn 120
A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter of the rivets is 7/8 in, and angles are each 4×31/2×3/8 in. For each rivets assume that the allowable stresses are T= 15 ksi and stress in b is 32 ksi. What is the bearing strength of the grinder? What is the bearing strengtht of the beam? What is the shear strength of the rivets? What is the maximum load that the connection can carry?