15 kipSpecificWeight y Elasticity E Rigidity G(Ib/in")Modulus ofModulus ofYield Strength (ksi)Materials(10) ksi(10) ksiTens. Comp.ShearA- Structural A36- Stainless 304- Tool L20.28429.011.03636Steel0.28428.011.03030Alloys0.29529.011.01021022 ft4 kip4 kipThe A-36 steel bar shown in the figure is made from two segment shaving crosOSS-Bsectional areas of AAB-lin^2 and ABD=2in^2.Determine the vertical displacement of end A and the displacement of B relative toC.1.5 ft8 kip8 kip|C1 ftD

Answered: Image /qna-images/answer/c1548b44-530c-4757-a05e-0a3fced73af9.jpg

Answered: Determine the vertical displacement of…

Engineering

Civil Engineering

Determine the vertical displacement of end A and the displacement of B relative t C.

Residential Construction Academy: House Wiring (MindTap Course List)

5th Edition

ISBN:9781337402415

Author:Gregory W Fletcher

Publisher:Gregory W Fletcher

Chapter4: Test And Measurement Instruments Used In Residential Wiring

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

sinav.gelisim.edu.tr/ExamUser/Take?examSessionld The yield imit for a typE of steel material is determined to k3600 keran. Detemine the permissible (allowable> tensile sress for this material acxording to S64S. (o r=) D 2,16 ton/cm² 23.60 ton /cm² 2 2,04 ton /cm² 1,44 ton /cm2 DBoş bırak Карat
7 30 Enercise:- diameter of 12mm A cylindrical rod 100 mm long with is subjected to a 30000 N. Assuming that the tensile load of deformation is entirely elastic and allowable elevation in pligmeter is allowable reduction in dligmeter is 0.015mm. choose amory only meeting requirent U (Poiss ons vahu) 0.33 below Material Aluminium alloy Bronze Titanium allow manimum 0.3 mm while manimum E (GPa) 70 100 110 0.34 3
7. ASTM suggests a tolerance of... percent to allow the variation in strength as a test of ....w. water. A. 12 В. 8 C. 10 D. 15 E. 16 F. None of them
kiv 01 A E = 200 GPA deformation BC deformationn AB total defomatiom of ABCD 5.34 mm O -5.34 mm O -0.88 mm 0.67 mm -1 mm O-3.5 mm 3.5 mm --0.75 mm O -7.11 mm 2m 20 sq mm 3 KN 2m 40 sq mm C 1.5 m 80 sq mm qkN
ok Strength of Materials donO نورا حياتها مترجر شریه ✓t مقادم نلود Dr. Mohammed Hashim Mohammed Problems tan't yorada grutegraat km). E1.x² (1) A steel rod with cross-sectional area of 150mm² is stretched between two fixed points. The tensile load at 20°c is 5 kN. What will be the stress at -20°c? At what temperature the stress will be zero? bedre α = 11.7x10 6/2 and E = 200x10² N/m².
Enter Delete Page End Down DETERMINE THE FORCES AT AL JOKTS 800 LB lo00 LB 13 15 4.5 2家 3.75 DETERMING THE AREA THE POSITION OF THE CENTROID ABOUT THE REFERENCE AXES AND THE MOMENT OF NERTIA ABOUT THE CENTROIDAL AXES OF THE COMPOSITE FI6URE
zain 10 2G 3G zain IQ Z Questions of Lectu... -> Questions of Lecture Five: Q1)) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3) yield strength and tensile strength 4) Modulus of elasticity and the strain hardening Q2)) Fill the following blanks: 1)) Tensile tests are used to 3)) The most application tests of applied static stresses to which materials can be subjected are ----------, ----------, ---------- 4)) Tensile stresses cause ----------, and compressive stresses ----------, while shear stresses --------, of the material. 5)) Engineering stress-strain is important in ---------, while the true stress-strain is important in ----------. 6)) The unit of mechanical stress is --------- or ----------, while the unit of strain is 7)) In compression test, when specimen is compressed, its height is ----------, and its cross-sectional area is ----------. 8)) Compression is in contrast to the tensile, the compression test contributes to the…
= 5.29 Knowing that P Q = 480 N, determine (a) the distance a for which the absolute value of the bending moment in the beam is as small as possible, (b) the corresponding maximum normal stress due to bending. (See hint of Prob. 5.27.) THEMOM DV P nedw to absol be500 mm 500 mm pripoly not Alase BOLERON 9T AO mersib anamorp sode bol ng appiled: the batuda Fig. P5.29 edi te ating out A Daniloobo CV. D (5.6b) Q f 12 mm s mas i nadw bozudiruaib ebimnice di Tibe sade 2b2 B (10. busd bus bris to pages. eda sdtlanbi are noe minnas li batalize yo led ditw i most u tamom gaiboedshus en betrovalmisoled loads Dignst Box brol 18 mm
pon 9.18 A steel rodin. in diameter and 25 ft long is subjected to an ace axial tensile load of 15,000 lb. Compute (a) stress ons Lanogsib & new (b) strain (c) total elongation aaste sviesiqmos srit nimmst gaites 900 viss srit .rwoda al
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in. Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A. (1) (2) Answer: UCIA - in.
The bolt and its head are circular in cross-section with diameters as shown. They are made of a material having a failure shear stress (Tri) of 170 MPa. (a) Applying a factor of safety (FS) of 3.5 against shear failure, determine the maximum allowable force P that can be applied to the bolt-rod so that the bolt-rod does not pull through the bolt-head. (b) For the force P, calculate the average shear stress in the 80-mm thick bracket. (as the 125-mm diameter bolt-head tries to punch it). -125 mm 116 mm 80 mm 60 mm
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to aodal loads as shown. If P-7 IN, Determine the total aodal deformation (in mm). Indicate negative sign f comoression. @ 5P O 3P E-200 6P 30 mm emm 80 mm 30 mn 30 mm