In a thin plate, the state of stress prevails according to the figure. Calculate the principal stresses and their directions (using both equations and Mohr's stress circle). Show the result in a figure. σx = 40 MPa; σy = 50 ; MPa and τxy = 30 MPa The question should contain clear solutions and be presented according to the following structure: Given, to find, Solution and Answer.

Q: The stress state at a point of a structure is shown in the figure below. Determine: (a) The stresses…

A: Given σx=45 MPaσy= 20 MPaζxy=50 MPa To find Stresses for element at 15o Principal stress

Q: A composite shaft consists of 3 cylinders that are made from aluminum, copper and steel. Multiple…

A: To findDetermine the normal stress in section AB, Determine the normal stress in section BC,…

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A:

Q: For each of the stress states listed below, find all three principal normal and shear stresses. Draw…

A: Find outFind all three principal, normal, and shear stresses. Draw a complete Mohr's three-circle…

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: The forces as given below are applied as shown in the figure. F1=10 kN, F2=5 kN and F3=3 kN. The…

A: a)  -159.15 MPa(Compressive) , 35.80 MPa(shear stress) b) Principle stresses 7.686 MPa ,-166.836 MPa…

Q: Part B The state of stress at a point is shown on the element. Take σ₂ = -15 ksi. Determine the…

A: For the solution refer below images.

Q: 1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr’s circle…

A:

Q: The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram.…

A: Given

Q: Example 4 If ox 80 MPa, oy = 0 MPa, and Txy = 50 MPa (cw), a) Using Mohr's circle, find the…

A: For solution refer below images.

Q: occur in the n-n plane of the figure. Present a diagram showing such stresses on the n-n plane.…

A:

Q: Mohr's circle is given to you. Assume o = 15.1 MPa. Indicate the normal stresses nd shear stress Try…

A:

Q: For the 2-Dimensional state of stress at a point represented by the following figure: (i) Determine…

A: According to our guidelines, we are supposed to answer the first three sub parts . Please repost the…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress, Each grid…

A:

Q: 1. A circular shaft with a keyway can be approximated by the section shown in Fig. r=b r 0 r =…

A: To Find : The value of constant K. Given : The prandtl stress function form is ψ=Kb2-r21-2acosθr The…

Q: In the figure, the normal stresses oa = 70 MPa, o, = 50 MPa, oc = 110 MPa on the faces of the…

A: Given that, σa=70 MPa,σb=50 MPa,σc=110 MPa,α=60°,β=45°, The general form of the equation of stress…

Q: ▾ Part B Determine the normal stress dy'. Express your answer to three significant figures and…

A:

Q: Determine the equivalent state of stress if an element is oriented 60° clockwise from the element…

A:

Q: 50 MPa 90 MPa 35 MPа 60 90 MPa 50 MPa 30

A:

Q: Q1// An element in the boiler is triaxially stressed, the stresses distribution is given by (see…

A:

Q: 90 MPA 60 MPA 20 MPA

A: Given that, σx=-20 MPa,σy=90 MPa,τxy=60 MPa, Steps to draw mohr's circle: 1. Take direct stress at…

Q: On a stress element, the following stresses are acting: σ x = 5 ksi (Compression) σ y =  10 ksi…

A:

Q: Q - The mechanism of bone as a solid rod shown in figure. The diameter is 4 cm and it is subjected…

A: Acting torque on the system = 200 ×0.15 =30 Nm Bending moment at end section = 200 ×0.25 = 50 Nm the…

Q: At a point in the cross-section of an engineering component an element is subject to the following…

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A: Given:The stress in the x plane is the stress in the y plane is The shear stress in the x-y plane is…

Q: Q1: A certain point in the mechanical part shown in Figure below. Use Mol determine: (a) the…

A: Givenσx=60 MN/m2=60MPaσy=-50MN/m2=-50MPaτxy=30MN/m2=30MPa

Q: - The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A:

Q: Electrical strain gauges were applied to a notched specimen to determine the stresses in the notch.…

A:

Q: A plane element is subjected to stress as shown in below figure. Determine the radius of the mohr…

A:

Q: Determine the principle stresses σ1, σ2, σ3 and their orientation φ, if σx, σy and σz are known as…

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

A:

Q: n a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} =…

A: Given:σx=20 MPaσy=80 MPaτxy=40 MPa

Q: A state of stress at a point A is given by ox = 45 MPa, oy = 9.1 MPa, and txy = -5.75 MPa. What is…

A: The given values are - σx=45 MPa, σy=9.1 MPa, ζxy=5.75 MPaThe principle stress is given by -  σ1 ,…

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A:

Q: Draw Mohr's circle that describes each of the following states of stress shown in Figure 5. 3 ksi 6…

A: given   state of stress for element shown in figure a  = -12 ksi = - 3 ksi      = 0  state of…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Need to determine normal stress σn or ( σx )  In the given answer normal stress is shown by σn  Data…

Q: 3 please help Provide Free Body Diagram, labeled with appropriate quantities to better understand.…

A: σ1=156.84MPaσ2=33.153MPaandθ=37.98°Explanation:

Q: Complete the Circle of Mohr depicted in the figure.

A: According to the given details in the question.The Mohr Circle is Completed

Q: Using Mohr's circle, determine the fol (1) the stresses acting on an element in (2) the principal…

A:

Q: At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress…

A: Given:σx=-30 MPaσy=15 MPaζxy=25 MPa

Q: Please work out c and d

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.