In the figure, the normal stresses oa = 70 MPa, o, = 50 MPa, oc = 110 MPa on the faces of the triangular element show the plane stress state. a = 60°, ß = 45°. Using transformation equations, calculate the stresses ox, Oy and Txy. Find the principle stresses and direction for this stress state. Draw the Mohr circle.

In the figure, the normal stresses oa = 70 MPa, o, = 50 MPa, oc = 110 MPa on the faces of the triangular element show the plane stress state. a = 60°, ß = 45°. Using transformation equations, calculate the stresses ox, Oy and Txy. Find the principle stresses and direction for this stress state. Draw the Mohr circle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calcuate Torsion and Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
In the figure, a force of 1 kN is applied by means of an arm connected to a shaft with a diameter of 50 mm. So, represent the stress state of point B on the element? b) Draw the Mohr's circle for the given stress member and calculate the principal stresses?
For the plane stress case in the figure, a) the direction in which the normal stress is zero, b) Calculate the direction in which the shear stress is zero. σx =7 N/mm2, σy =7 N/mm2, τxy =24 N/mm2
Just complete the last part of this problem please (part 4). The mohr's circle drawing will help with a complete understanding of these types of problems.
At a point on the surface of a pressurized cylinder, the material element is subjected to stresses; σx = 60 MPa, σy = - 40 MPa, and τxy = - 30 MPa. Construct Mohr’s circle, then use it to determine the following: Do not use the equations of transformations.1- The principal stresses and the maximum shear stress.2- Show these stresses on sketches of properly stress elements.3- A point on the circle where the element is only subjected to pure shear stress. Calculate the value of that pure shear stress.
The state of plane stress at a point is presented by the stress element shown in figure 2. find the stresses acting on an element oriented at 30° Clockwise. With respect to the orignal element.also draw neat and to the scale Mohr's circle of the given problem. Take X=4740
Q-1 Figure Q-1, below, shows Mohr's cirde for a point in a physical object that is subjected to plane stress. (a) Determine the stresses Ox, Oy, and Txy, and show them on a stress element, properly orientedwith reference tox-y axes. (b) Determine the principal stresses o1, 02, and Tmax and show them on a stress element properly rotated with respect to the x-y element (c) Determine the stresses ơn, Ot and Trt, and show them on a stress element that is properly rotated with respect to the x-y element The sketches must indude the magnitude of the angles w.rt. positive x-axis as well as the angle between the x and n axes, and an indication of the direction of rotations (1.e., either clockwise (c.w.) or counterdockwise (c.C.w.)). 1 grid square 3 MPa
3. An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses of magnitude 35 MPa in the horizontal direction and tensile stresses of magnitude 10.5 MPa in the vertical direction (see figure part b). Also, shear stresses of magnitude 12.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40° from the horizontal. Show these stresses on a sketch of an element oriented at this angle. (a) 10.5 MPa Ţ (b) 35 MPa 12.5 MPa
Question 2) arm of Figure B from point x z plane, a horizontal angle of θ = 38 ° angled F = 29 kN force sized and C from the point z direction M = 17 kn.m acts a moment in size. The lengths of the arm are also given as L 1 = 1.5 m and L 2 = 1.1 m . It is desired to determine the stress state of point A on the aa section taken from the arm. The radius r of the section is r=0.015 m and the shear modulus of the arm material is also G = 78 Gpa . According to this; Question 2-C) Find the normal stress caused by the normal force at point A ( Write your result in MPa .) Question 2-D) Find the normal stress caused by the bending moment at point A. (Your result MPa in the size of your font.)
Please show full work than you
EMFT
The stresses shown below act on horizontal and vertical planes through a point on the surface of a stressed body. Use Mohr's circle to determine (a) The principal stresses and the maximum shear stress at the point. (b) The normal and shear stresses on the inclined plane A-B shown in the figure. A 6 ksi 45° 10 ksi B