1. Given a combination of stresses on an element shown in the figure,(a) draw a Mohr's circle representing the complete state of stress of the element, i.e. show prinicpal stresses(01,02), maximum shear stresses (Tmax), principal direction (0p), original orientation, and original stresses(Ox, Oy, Txy).(b) draw three-dimensional Mohr's circles showing the three principal stresses and absolute maximum shearstress.Oy = -50 MPaTxy20 MPaOx = -150 MPa

Answered: Image /qna-images/answer/0a46a7b2-5b9c-4d09-a116-1f1a109f283f.jpg

1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr’s circle representing the complete state of stress of the element, i.e. show prinicpal stresses (01,02), maximum shear stresses (Tmax), principal direction (0,), original orientation, and original stresses (Ox,Oy, Txy). (b) draw three-dimensional Mohr's circles showing the three principal stresses and absolute maximum shear stress. Oy = -50 MPa Txy = 20 MPa Ox = -150 MPa

1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr’s circle representing the complete state of stress of the element, i.e. show prinicpal stresses (01,02), maximum shear stresses (Tmax), principal direction (0,), original orientation, and original stresses (Ox,Oy, Txy). (b) draw three-dimensional Mohr's circles showing the three principal stresses and absolute maximum shear stress. Oy = -50 MPa Txy = 20 MPa Ox = -150 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.8P: An element in plane stress on the fuselage of an airplane (figure part a) is subjected to...

See similar textbooks

Similar questions

During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
(b) Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation law for the stress system. Use Mohr's circle to determine the stresses on an element inclined at 30° clockwise to the state of plane stress system as shown in Figure 1 and show the corresponding stress elements. Q2 (a) It is important im 80 MPa 50 MPa Ľ 50 MPa Figure 1 80 MPa 25 MPa
The state of stress at a point on a thin plate is as shown in the left side of the Figure below. Determine the state of stress (ox, oy, txy) represented on the element oriented as shown on the right. 120 Sigma_x^prime (MPa) 200 Sigma_y^prime (MPa) 60 Tau_xy^prime (MPa) 30 Alpha (degrees) O x' Oy Txy' Txy Ox
Given a stress state of ø, = -4 MPa, øy = 12 MPa, ty = 7 MPa ccw 1) Draw a properly oriented stress element illustrating this state of stress 2) Using Mohr's circle, find the principal stresses and directions, and show these on a stress element correctly aligned with respect to the xy coordinates. Draw another stress element to show zi and 72, find the corresponding normal stresses, and label the drawing completely. 3) Use the plane-stress transformation equations to validate your answers in part 2
The state of stress at a given point is given in the following figure. Use Mohr’s circle to find: a) The principal stresses b) The maximum in-plane shear stresses. For both cases you must draw a rotated element including all stresses and the angle of rotation. You must draw a properly labeled Mohr’s circle.
Q: The soil element with known stress conditions is shown in following figure. (i) construct Mohr's circle for the soil element and determine (ii) stress condition of the plane AC (use double angel method); (iii) major and minor principal stresses; (iv) the angle between major principal plane and the plane "AD" ; (v) maximum shear stress. Provide your answer up to one decimal point. [use graph paper to draw Mohr's circle] 2 kN/m² 6 kN/m² + + B D 2 kN/m² 2 kN/m²
2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m? (tensile) and 70 MN/m2 (Compressive). The shear stress across the planes is 65 MN/m2. Find the following by Mohr's Circle method and compare with Analytical solutions: (i)The Normal stress on a plane making an angle of 50° with the plane of first stress. (ii)Shear stress on the plane (iii) Maximum shear stress (iv) Resultant stress and it's direction. (v) Major and minor principal stresses.
The stresses acting on element A in the web of a train rail are found to be 'X (MPa)' tension in the horizontal x-direction and 'Y (MPa)' compression in the vertical y-direction. Also, shear stresses of magnitude 'S (MPa)' act in the directions shown in the figure. Draw Mohr's circle for the state of stress. Determine the stresses (Ox', Oy' and Txy') acting on an element oriented at an angle 'D' from the horizontal Show these stresses on a sketch of an element oriented at this angle X=45MPA,Y=150MPA,S=52MPA,D=-40 Degree
1) The state of stress on an element is shown in following figure. i) Determine the stresses acting on an element oriented at a counterclockwise angle of 48° from the horizontal. Show these stresses on a properly oriented element. ii) Determine the principal stresses and the principal angle. Show these stresses on a properly oriented element. iii) Determine the maximum shear stress, angle for maximum shear stress and normal stresses when maximum shear stress exists. Show these stresses on a properly oriented element. 140 MPa A 42 MPa 60 MPa
For each of the plane stress states listed below, draw a Mohr's circle diagram properly labeled, find the principal normal and shear stresses, and determine the angle from the r axis to of. Draw stress elements as in Figure 3-11c and d and label all details. a.) sigma,x = - 12 kpsi, sigma,y = 22 kpsi, txy = 12 kpsi cw b.) sigma,x = 30 kpsi, sigma,y = -10 kpsi, txy = 10 kpsi ccw c.) sigma,x = -10 kpsi, sigma,y = 18 kpsi, txy = 9 kpsi cw Attached is an image of Figure 3-11c and d for example. THIS IS THE ONLY INFORMATION I AM PROVIDED WITH! Thank you for the help in advance!
A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.
Consider the following plane stress state: Ox=30 MPa, y= -60 MPa, Txy= 30 MPa cw Calculate the following: 1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis ( 2. Principal normal stresses (01, 02) The principal normal stresses are σ₁ = 39.08 3. Maximum shear stress (7) The maximum shear stress is 54.08 MPa. 4. The angle from the x axis to 0₁ (p) The angle from the x axis to 0₁ (p) is -16.85 5. The angle from the x axis to 7 (s) The angle from the x axis to T (s) is 28.15 6. The radius of the Mohr's circle The radius of the Mohr's circle is 54.08. ✰ MPa. MPa and 02 = -69.08 MPa. O -15 MPa, CW CCW O MPa).