Good evening,Guidance on this please. Thanks! The following 3-phase balanced loads are connected in parallel across a 3-phase Wye-connected, 60 Hz source of 4160 Volts line-to-line.Load #1120 kVA at 0.8 PF lag (Wye connected)Load #2180 kW at 0.7 lag (Wye connected)Load #313 Amps phase current, unity PF (Delta connected)a) Find the total complex power consumed by the three loadsb) Find the total source line current (magnitude)c) Find the CAPACITANCE needed per phase (for a Delta connection) sothat the overall power factor is 0.95 lagd) Find the new source line current with the 3-phase bank of capacitorsinstalled.

Given data: -load 1−120 KVA at 0.8PF lag (wye connected)load 2−180 KVA at 0.7PF lag (wye…

Answered: Good evening, Guidance on this please.…

Engineering

Electrical Engineering

Good evening, Guidance on this please. Thanks!

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30P: Figure 2.26 shows three loads connected in parallel across a 1000-V(RMS),60Hz single-phase source....

See similar textbooks

Related questions

Q: Given the angular frequency is w = 600 radians/sec, determine the equivalent impedance Z in…

A: In this question, we need to determine the equivalent impedance. we know , inductive reactance XL =…

Q: a) I(O-) equals b) I at infinty time equals A c) The time constant t equals d) I at t=5ms equals A A…

A: In this question, we need to determine initial current in inductor, current at time t= ∞, time…

Q: Rs e = 10 Vrms 13sd=1 MA Rsh=500 Rm-500 Each diod has an average forward resistance of 50 and is…

A: Full frequency converter-A full frequency converter is defined as a type of converter that converts…

Q: If you double the impedance of a transmission line you will double the inductance per unit length. T…

A: Given statement is false Explanation:

Q: Surge impedance of 3 Phase, 400 kV transmission line is 200 Q. The surge impedance loading of the…

A: We need to calculate surge impedance loading for given transmission line.

Q: 4.4

A: VRMS = 3VExplanation:

Q: For circuits (2a) and (2b) above, solve for the current through resistor R3 and the power dissipated…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Find the Power by the 4 k ohm's resistor.

A: In the given question we need to calculate the power absorb by 4k ohm resistor.

Q: For the circuit given in Figure 2, with R₁ Draw the output voltage waveform at point A. =2k,…

A: According to the question, for the circuit shown belowWe need to draw the output waveform.

Q: Consider a complex linear circuit that is expressed as an equivalent circuit containing the Thevenin…

A: For the given circuit the validity of the given statement needs to be identified.

Q: Please solve the question: Subject (Communication Systems)

A: positive infinity ∞Explanation:Sure, let's evaluate each integral step by step.1. Integral of Dirac…

Q: 1) [7 marks] Fill up the below state table by converting your most right two digits of your student…

A: a) If you find the solution doubtful or doesn't match with your answer provided, or you feel that I…

Q: 7.21 Ignoring reflection at the air-soil boundary, if the amplitude of a 3 GHz incident wave is 10…

A: According to the question, we need to find depth.

Q: - A 100 W lightbulb has a resistance of about 12 when cold (20 deg * C) and 156 when on (hot).…

A: The objective of the question is to estimate the temperature of the filament when hot, given the…

Q: Calculate Fourier Series of the f(t). Please verify your result by plotting it up to 7th harmonic.…

A: A periodic signal is given byWe need to determine the Fourier series representation of the signal…

Q: A - Let the following resistor be a lightbulb. The switch S is initially at position a for a long…

A: In the given question we need to check the operating conditions of bulb.

Q: Find the Thévenin equivalent with respect to the terminals a, b in the circuit in (Figure 1).…

A: The circuit diagram,

Q: You are handed a black box containing a circuit with two terminals marked a and b. With nothing else…

A: Thevenin voltage is 15 V, the Thevenin resistance is 0.4 ohms, and the resistance of the external…

Q: A conductor of length = 1 m with a current = 60 A is placed perpendicularly to the field lines in a…

A: The magnitude of electromagnetic force on the wire is, Fmag=36.0NExplanation:Step 1:Step 2:

Q: Compute for the resistance of (i) silver, (ii) copper, and (iii) aluminum wire using these Equations…

A: The objective of the question is to calculate the resistance of silver, copper, and aluminum wires…

Q: An oscilloscope is to be have an in resistance of 8Mr, a sensitivity of and attenuation factory…

A: The attenuation resistance, also known as the input impedance, of an oscilloscope refers to the…

Q: Q#3: A single-phase transformer has the following specifications Apparent Power (S) = 10 kVA Primary…

A: The apparent power, Primary voltage, Secondary voltage, The frequency,

Q: Help with question 4

A: (a) The equivalent winding resistance (Reh) of the transformer at the high-voltage side is…

Q: 2.6

A: Detailed solution is provided below.Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Consider the control system shown below. G₁(S) R(s) 2 Y(s) K (s + 1) s(s+4) 3 (s²+2s+5) Find: Gp(s)…

A: Given:a control system,we need to find the Gp(s) so that the steady state error for step input is 0.

Q: Solve problems by solving ana explaining eeach step

A: (a) v=48V(b) P=374.4W Please comment if you have any doubts. I will reply asap.Explanation:

Q: Use Nodal analysis to find (a) current flowing through all the branches in the following circuit-3…

Q: Part A An acb sequence balanced three-phase Y-connected source supplies power to a balanced…

A: The source voltage of phase a,The per phase line impedance, The load impedance per phase,

Q: Present Next State State x=0 x=1 x=0 Output x=1 yayı Y2Y1 Y2Y1 Z N 00 00 01 0 0 01 00 10 0 0 10 00…

Q: Define what is used to determine the "steady state" of the charge/discharge phase of an RC Circuit.…

A: The given circuit isWe need to define the paramemter used to determine the "steady state" of the…

Q: 9. Find Io 12/0°V 102 ww 2/0° A 1Ω 1Ω

A: Given circuit is, Asked to find the current Io =?

Q: The switches shown in the diagram have been in this position for a long time prior to t = Os, use…

A: The current is IL(t)=(20+80e-500t)mA for 0<t<2 sec, IL(t)=(30-10e-250(t-2) )mA for t>2…

Q: Question:- A):Explain the effect of increasing the field resistance in a DC shunt generator while…

A: A. Explain the effect of increasing the field resistance in a DC shunt generator while operating at…

Q: Build a karnaugh Map for this function table [[A, B, C, D, F b) What is the simplest minimum…

A: The given function table is shown below,

Q: 3. Calculate the battery current in the circuit below. www 202 www w ми 0.5. 252 ww I ww 0.5 Hint:…

A: A resistor is a passive two-terminal electronic component that opposes the flow of electric current.…

Q: Find the equivalent resistance between points A and B in the drawing. Number i Units A 3.0 Ω ww 20.0…

Q: Using D flip-flops, design a logic circuit for the finite-state machine described by the state…

A: A D flip-flop, also known as a data flip-flop or delay flip-flop, is a type of digital logic circuit…

Q: 3.1

A: The period of the wave form is T=4sExplanation:Step 1:Concept: Time period of wave form Step 2:

Q: 2.7

A: Ans. The 2€ coins are larger then the 1€ coins.Explanation:

Q: The NMOS transistor shown below shows V₁ = 0.5 V and k = 2 mA/V². Sketch and clearly label in versus…

Q: Please solve p1 of this question which also includes the matlab code by using the functions for…

A: Given:we need to do:1) Express in terms of .2) Verify the result using MATLAB.

Q: In the following circuit, vs(t) = 6-3u(t) V, R = 400 2, L = 4 H, C = 0.0001 F The complete response…

A: Given:with we need to find: the value of B.

Q: Find the charge q(t) on the capacitor and the current i(t) in the given LRC-series circuit. L = 1 h,…

A: Given:For a series LRC circuit, withwe need to find:a) charge on the capacitor,b) current flowing…

Q: For the circuit below if the switch is closed for t0 find the following: 40 Ω ти + 10 Ω www 25 μF…

A: Giiven here a circuit and asked to find voltage and time constant.

Q: The magnetic circuit shown below has mean magnetic path of 0.5 m, a relative permeability of 1000,…

A: the inductance of the coil is 18.095616 mH or 0.018 H.Explanation:

Q: 7.8.50 Use source transformation to find V, in the circuit in Fig. P7.8.50. 2/0°A 50 4/0°V w 202 ΖΩ…

Q: Problem 3: Question Consider the circuit diagram below. If two identical capacitors, each with a…

Q: 2 a. For the following circuit Write the voltage of the sources in time domain. b. Using mesh…

A: In the given question we need to calculate the output voltage and Rth

Q: 1.2

A: The equivalent inductance is Leq=100mH.Explanation: When two inductors L1 and L2 are connected in…

Q: Sometimes "bubbles" are used to indicate inverters on the input lines to a gate. What are the…

A: In the given questions we need to calculate the equivalent logic gate of the given logic circuit.

Concept explainers

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors. The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.

Question

100%

Good evening,

Guidance on this please. Thanks!

The following 3-phase balanced loads are connected in parallel across a 3-
phase Wye-connected, 60 Hz source of 4160 Volts line-to-line.
Load #1
120 kVA at 0.8 PF lag (Wye connected)
Load #2
180 kW at 0.7 lag (Wye connected)
Load #3
13 Amps phase current, unity PF (Delta connected)
a) Find the total complex power consumed by the three loads
b) Find the total source line current (magnitude)
c) Find the CAPACITANCE needed per phase (for a Delta connection) so
that the overall power factor is 0.95 lag
d) Find the new source line current with the 3-phase bank of capacitors
installed.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: About question.

VIEW

Step 2: Total complex power and ttal source line current.

VIEW

Step 3: Value of capacitance and new source line current.

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure 2.26 shows three loads connected in parallel across a 1000-V(RMS),60Hz single-phase source. Load 1: Inductive load, 125kVA,0.28PF lagging. Load 2: Capacitive load, 10kW,40kvar. Load 3: Resistive load, 15kW. (a) Determine the total kW, kvar, kva, and supply power factor. (b) In order to improve the power factor to 0.8 lagging. a capacitor of negligible resistance is connected in parallel with the above loads. Find the kvar rating of that capacitor and the capacitance in F. Comment on the magnitude of the supply current after adding the capacitor.
The following 3-phase balanced loads are connected in parallel across a 3- phase Wye-connected, 60Hz source of 4160 Volts line-to-line. Load #1 120kVA at 0.8 PF lag (Wye connected) Load #2 180kW at 0.7 lag (Wye connected) Load #3 13 Amps phase current, unity PF (Delta connected) a) Find the total complex power consumed by the three loads b) Find the total source line current (magnitude) c) Find the CAPACITANCE needed per phase (for a Delta connection) so that the overall power factor is 0.95lag d) Find the new source line current with the 3-phase bank of capacitors installed.
Two balanced Y-connected loads in parallel, one drawing 15 kW at 0.6 power factor lagging andthe other drawing 10 kVA at 0.8 power factor leading, are supplied by a balanced, three-phase,480-volt source.d. ∆-connected capacitors are now installed in parallel with the combined load. Whatvalue of capacitive reactance is needed in each leg of the ∆ to make the source powerfactor unity? Give your answer in W.e. Compute the magnitude of the current in each capacitor and the line current from thesource
The following information is given in connection with three loads that are connected in parallel to a 230 volts ac line. Load 1: 4.6KW at unity power factorLoad 2: 11.5KVA at lagging power factor of 0.62Load 3: 5.52KW at leading power factor of 0.8 Calculate the:a. Total currentb. Overall power factor c. Total power d. Total reactive power e. Draw the phasor diagram of the current
The following information is given in connection with a load circuit consisting of two parallel branches: Z1 = 4.8 /25o ohms, Z2 = 3.75 /-72o ohms, I1 = 50 amperes, and I2 = 64 amperes.Calculate: a) the equivalent impedance b) the total voltage c) the currents I1 and I2 if the total voltage is used as reference d) the total real, reactive, and apparent powers e) the overall power factor.
A star-connected three phase power pack is connected to balanced star-connectedload of 2 + j3 Ω. The line current is 2∠0⁰ A. Assuming negligible impedance onthe cable, calculate:a) the phase and line voltages from the source. b) the real and reactive powers of the circuit.
Q2 In Industry, three Inductive loads, each of resistance R = 32 ohms and inductance L = 0.04 H are connected in Delta to a 425 V, F = 50 Hz, 3 phase supply. Find the following below: i) Phase Impedance, Zp = ii) Phase Voltage, Vp = iii) Phase current, Ip = !3! iv) Line current, I= iiv) The Total Power Consumed, P=
ABC phase sequential In a three-phase balanced Star-Star connected system, the phase on the source side voltage is 300 Vrms. The line impedance in the system is Zhat=1 ohm. star bound Each of the loads has a capacitive load of 5-j3 ohms and an inductive load of 9+j2 ohms. is the parallel connected form of the load. In the light of this information, a) Find the real power provided by the source. b) Determine the power factor of the source.
3. A balanced Y-connected load with phase impedance of 5 Ohms @ 12 degrees is connected to a 3-phase source with a line-to-line voltage of 220 Vac. a. find the magnitude of the current in each line 25.4 <-12 degrees A b. find the power factor 0.978 logging c. calculate the total complex power 9.678 <12 degrees kva d. calculate the total real power e. calculate the total reactive power
11. A 3-, 400-V symmetrical supply feeds a star-connected load consisting of non-reactive resistors of 3, 4 and 5 connected to the R. Y and 8 lines respectively. The phase sequence is RYB. Calculate (1) the load star point potential (i) current in each resistor and power dissipated in each resistor. (i)34.5 V (ii) 664 A, 59.7 A. 51.8 A (iii) 13.22 kW, 14.21 kW, 13.42 kW) Answer Need Asap will surely upvote
The following information is given in connection with a load circuit consisting of two parallelbranches: Z 1 = 4.8/25 o ohms, Z 2 = 3.75/-72 o ohms, I 1 = 50 amperes, and I 2 = 64 amperes.Calculate: a) the equivalent impedance; b) the total voltage; c) the currents I1 and I2 if the totalvoltage is used as reference; d) the total real, reactive, and apparent powers; e) the overallpower factor.
In Industry, three Inductive loads each of resistance = 32 ohms and inductance L = 0.16 H are connected in Delta to a 400 V, F = 50 Hz, 3 phase supply. Find the following below: Phase Impedance, Zp = Phase Voltage, Vp = Phase current, Ip = Line current, I= The Total Power Consumed, p =