Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor with internal resistance of 0.34 ohm and reactance of 47.15 ohms; and a capacitor with reactance of 7.53 ohms. Compute for the magnitude of its equivalent impedance in ohms.

Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor with internal resistance of 0.34 ohm and reactance of 47.15 ohms; and a capacitor with reactance of 7.53 ohms. Compute for the magnitude of its equivalent impedance in ohms.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Related questions

Q: Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor…

Q: a) To the coil of a henry, measure its internal resistance and the value of the inductance. b)…

A: Resistance is property to oppose current, the unit of resistance is Ohm. Inductance is the property…

Q: A fault current limiter as shown in the figure, has L1 = 1 mH and a total impedance of j10 Q. If the…

A: The given circuit is as shown below,

Q: In the Distribution Line Simulator, the Distribution Line is connected in Nominal-Pi Circuit. Select…

A: Ans -1) - False In case of nominal pi circuit Due to the capacitance connected in the parallel to…

Q: The rms input voltage to the circuit in Figure 3.20a is 120 V, 60 Hz. (a) If the dc output voltage…

A: Given: The RMS input voltage to the circuit in the figure below is 120 V, 60 Hz. To find: (a) If…

Q: 1. Peak to peak ripple is defined as a) The difference between average dc voltage and peak value b)…

A: 1. Peak to peak ripple is defined as The difference between the maximum ac and average dc voltages.…

Q: An ac generator provides emf to a resistive load in a remote factory over a two-cable transmission…

A: (a) Note- There is silly mistake in the (a) part of the Question, Question should be what is the…

Q: 2. Isolated power systems installed in healthcare facilities are required to A. have an…

A: Power system:- It is a connection of electrical components. Power plant, transformer, transmission…

Q: What is nodal analysis/node-voltage method for Ac circuits. Also, please give me atleast 2 circuit…

A: NODAL ANALYSIS/NODE ANALYSIS FOR AC CIRCUITS: 1. One method of calculating the current and voltage…

Q: QI/ Choose the letter of right choice only for the following: 1. Average value of a sinusoidal…

A: In this question, We need to choose the correct options We know V= IZ as per our company guidelines…

Q: Q5/A/ Calculate the maximum and minimum current in this conditions.(1- have maximum tran smission,…

A: 1. For maximum transmission, Transmission line should be matched. So for matched transmission line…

Q: a) Define the complete response in transient circuits? b) Plot [v() =5u(-t+1) - Su(-t- 1)]? c) What…

A: Note: Since you have posted a question with multiple subparts, we will solve the first three…

Q: Enumerate five step-by-step procedures of Maximum power transfer theorem method in application to ac…

A: MPT theorem: This is used to find the maximum power in the load.

Q: What is the general reason for selecting the capacitor voltage with a value greater than 400 V (such…

A: The capacitor is required to inject reactive power into the transmission system.

Q: Q.5. (E3 10) State True or false a- The DC load flow study is an iterative process b- In a load…

A: Since we are allowed to solve only up to three sub parts in a question the solution below contains…

Q: Q2) Open with Google Docs Design a CT-FWR to supply a load of (502) with a waveform of the following…

A: Design a CT-FWR to supply a load =50 ohm Vdc = 12 V Ripple factor = 0.1 % the main power supply is…

Q: What is the electrical length of the transmission line measured from the source to the load if the…

Q: A single-phase swimming pool pump motor consumes a power of 12 kVA when supplied by a sinusoidal…

Q: the balanond three phase paralel cireuit belew.complete the tables uing the provided values Assuming…

Q: The net inlet to a factory powered by a 2300 volt infinite bus is measured as 765 A, for a lag 0.92…

A: The solution can be achieved as follows.

Q: 15. A solenoid coil with a resistance of 50 ohms and an inductance of 250mH is connected to a…

Q: Determine the effective resistance Rin of the network exhibited in the figure. Each Ris 2.2n A…

Q: For the circuit shown, solve for IB, IC, VCE, IC(sat) and VCE(off). Also, construct a dc load line…

A: BJT is current controlled electronic device in which their mode of operation controlled by base…

Q: Using Eq. (5.23), determine the capacitancc to neutral (in µF/km) of a three-phase linc with threc…

A: Three Phase Line: Electrical power lines are used in an electric power system to transport electric…

Q: For the circuit shown, solve for IB, IC, VCE, IC(sat) and VCE(off). Also, construct a dc load line…

A: The circuit diagram is shown below, Where,RB=390kΩRC=1.5kΩβ=150

Q: Q.4. Find the rms value of lo and VAB =? in the circuit shown below.

Q: a.) determine the undamped natural frequency b.) determine the damping ratio c.) determine the…

Q: 2. a) Adjust Vab = 20 Vpp and the frequency as 100 Hz, 500 Hz, 1 KHz, 50 KHz, 100 KHz then measure…

Q: Q1: For the circuit shown below, determine Re

Q: Determine the value of Rµ for the maximum power transfer, Pmax to occur and calculate the maximum…

A: Thevinins theorem for DC circuit here Providing The procedure is quite same for AC also It is also…

Q: For a 152 kV, 60 Hz system, the capacitance up to the location of the circuit breaker is 0.020…

Q: 15. A solenoid coil with a resistance of 50 ohms and an inductance of 250mH is connected to a…

Q: 1. Peak to peak ripple is defined as a) The difference between average dc voltage and peak value b)…

A: The solution is given below. The answer for question 4 is option d.

Q: The resistance and inductance of a coil can be obtained by connecting the coil in series with a…

A: From given values find the phase angle of coil voltage . Then find the impedance if coil then…

Q: Directions: At the end of each solution (per item) should contain the signature (over printed name)…

Q: 2. Distribution factor proportional with......

A: Note: As per our rule we’ll answer the first question since the exact one wasn’t specified. Please…

Q: The resistance and inductance of a coil can be obtained by connecting the coil in series with a…

A: The solution is given below.

Q: How much is the Zt for a 20-Ω resistor in series with a 20-Ω capacitive reactance? If a 20 V is…

Q: ) A 3-phase, half-wave thyristor converter is connected through a voltage source 150 V as input…

Q: The percent values of the voltage, current, impedance, and volt-amperes for a given power system are…

Q: rt Problem: Given a series circuit comprised of the following element: 67.03-ohm resistor, practical…

Q: Enumerate five step-by-step procedure of Mesh analysis method in application to ac electric circuit…

A: Mesh is a loop which does not contain any inner loop. It is applicable only for the planer network…

Q: Part a) when is it appropriate to use instantaneous, peak, and RMS quantities Part D

A: Instantaneous, peak and RMS quantities are important in determining the extent and the value of the…

Q: Q3// Power is supplied to a load resistor R from a three-phase zero-impedane voltages using…

A: Given: Power is supplied to a load resistor R from a three-phase zero-impedance supply of balanced…

Q: Q3) In the transformer-coupled filter-bridge circuit show, answer the following questions:…

A: It is given that: RAΩ=500ΩVsecondary=30VrmsVrpp=0.4V

Q: The resistance and inductance of a coil can be obtained by connecting the coil in series with a…

Q: Braw the circuit diagram and specify the component

Concept explainers

Differential amplifier

There are two amplifying stages with common degeneration in a differential amplifier.

Question

Do not round off during computation. Finals ans should be 4 decimal places

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
4) Determine the value of voltage across resistor and capacitor5) Convert in rms values
An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by
In a series circuit with the following devices to a 230volts 60Hz supply with a resistor in the range of 300 ohms and 990 ohms. What are the steps in calculating the impedance ...
low voltage systems What is the general reason for selecting the capacitor voltage with a value greater than 400 V (such as 415,445 V) in Reactive Power Compensation? a) Reduce losses b) Harmonics C)Current decrease d) Voltage drop
A 250-V circuit, consisting of a resistor, an inductor and a capacitor in series, resonates at 50 Hz. Thecurrent is then 1A and the p.d. across the capacitor is 500 V. Calculate (i) the resistance (ii) theinductance and (iii) the capacitance Answer:
Question 4 A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its minimum is no less than 50% of its average. Furthermore, the output voltage ripple is less than 1%.
Reduce to its simplest form using msop
A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
A series circuit consists of a resistor, a coil, and a capacitor connected across a 300 V, 60 Hz AC source. THe current drawn is 20A. The voltage across the resistor is 60 V, that across the coil is 260 V and that across the capacitor is 100V. The resultant voltage across the coil and the capacitor is 254.56 V. Determine (a) the resistance of the resistor, (b) the resistance and inductance of the coil, and (c) the resistance and capacitance of the capacitor.
please solve value of Capacitor with 0.1V Ripple. And draw output ripple waveform. Explain it one by one for me thanks..