Q3) In the transformer-coupled filter-bridge circuit show, answer the following questions: Ra.(0)=500 120 V ms 60 Hz RA a) If the secondary voltage is 30 Vrms, Vrpp = 0.4 V, determine the value of the capacitor C. b) Calculate the de output voltage VDc and the ripple factor r. c) Detemine PIV. Which ofthe following PIV rating values is considered to be a suitable one to be used for the diodes in this circuit: 40 V or 60 V. Explain your answer. 00000 00000

Q3) In the transformer-coupled filter-bridge circuit show, answer the following questions: Ra.(0)=500 120 V ms 60 Hz RA a) If the secondary voltage is 30 Vrms, Vrpp = 0.4 V, determine the value of the capacitor C. b) Calculate the de output voltage VDc and the ripple factor r. c) Detemine PIV. Which ofthe following PIV rating values is considered to be a suitable one to be used for the diodes in this circuit: 40 V or 60 V. Explain your answer. 00000 00000

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. The average power consumed by a resistance is equal to .. in non- .... ... sinusoidal input signal. *
drive a formula for (SNR) of sinusoidal signal has been sampled and quantized.
ument-460F8C6BE9D6- x 5-1.pdf CD Page view A Read aloud 1: Theory 1.1 Describe briefly a sinusoidal signal and ALL its properties. Give example with figures. ongingoring which is si +.
McqThe RMS current via the SCRS of the Bidirectional ac chopper is ................- of the RMS output current 0.5 0.775 1 0.707
Part 1) Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is resistive with R=10 Ohms. The critical value of L and the critical value of C are equal to: a. 0.625mH and 0.392uF b. 0.625mH and 0.196uF c. 0.312mH and 0.196uF d. None of these Part2) Now consider the same given but the load is an inductive load with R=10 Ohms and L=10 mH. The switch is ideal. Calculate The RMS load current Io and the RMS converter current Ir are equal to: Select one: a. 5A and 3.54A b. None of these c. 8A and 5.66A d. 12.5A and 8.84A
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Vot Vm = 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. Vip = 0.1 V (assume ideal diodes) T=0.01 sec. tisec) Q3) V in Design a regulated circuit to supply a constant voltage of (10 V) across a resistive load of (50 2). The input voltage is shown in the figure. The minimum current for the Zener diode operation is (Izk=5mA). Find the 15 V 15 maximum power dissipated in the Zener diode. 12.5 12 V 10
Consider a step down converter supplied by a DC power source of magnitude Vs = 220 V. The switching period is 0.1 ms and the duty cycle k is set to 0.5. The load is an inductive load with R=5 Ohms and L=10 mH. The switch is ideal. The RMS converter current IR is equal to 15.56A. The ripple factor of the input current RFs would be equal to: Select one: a. 0% Ob. 50% Oc. 100% d. None of these
Design a CT-FWR to supply a load of (50N) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
Consider a step down converter with a resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is 0.25 ms and the duty cycle k is first set to 0.5. The load is an inductive load with R=10 Ohms and L-10 mH. The switch is ideal. The average source current is 4A. The ripple factor of the input current RFs is equal to: Select one: O a. None of these O b. 0% C. 100% d. 50% Clear my choice
Mcq Q1) What is the benefit of using two pulse transformers to drive the SCR of a single-phase bidirectional AC voltage controller? * - to isolate the SCRs from the source - to isolate the SCRs from getting short - to isolate the load from the source to control the rms output voltage
Consider a step down converter supplied by a DC power source of magnitude Vs = 220 V. The switching period is 0.1 ms and the duty cycle k is set to 0.5. The load is an inductive load with R-S Ohms and L-10 mH. The switch is ideal. The RMS converter current IR is equal to 15.56A. The ripple factor of the input current RFs would be equal to: Select one: O a. None of these O b. 0% OC. 100% O d. 50%
a carrier frequency 10⁶ and amplitude 3V frequency modulated by a sinusoidal wave of frequency is 500 HZ and the peak amplitude 1 Volt as a consequence , the frequency deviation is 1 KHz. The level of the modulating waveform is changed to 5 Volt peak and the modulating frequency is changed to 2KHz. Write an expression for the new modulated waveform.