I need the answer as soon as possible Q2)Open with Google DocsDesign a CT-FWR to supply a load of (502) with a waveform of the followingspecifications: -• Vdc = 12 VRipple factor = 0.1 %the main power supply is (220 Vrms, 50 Hz).Determine the following values: -1- The value of capacitor filter.2- The maximum load voltage (VmR)3- The transformer turns ratio (a).4- The RMS value of the load voltage.5- Draw the output waveform.(assume ideal diodes)Q3)Design a voltage regulator eircuit to supply a constant voltage of (10 V) across a resistiveminimum Zener current is (50 mA) and maximum current is (800 mA).(100) TIII

Design a CT-FWR to supply a load =50 ohm Vdc = 12 V Ripple factor = 0.1 % the main power supply is…

Answered: Q2) Open with Google Docs Design a…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer turns and magnetizing inductance, switching frequency and capacitor to limit the ripple voltage less than 0.5%.
low shows the circuit diagram of the linear variable differential transformer (LVDT). Figure 2 The primary coil is sinusoidally excited. (e) Clearly explain its operation when the core is moved from side to side (b) Given that the excitation frequency is much higher than the frequency of movement of the core, draw waveforms to show the output voltage for the following displacement waveforms. Xi Comment on your output waveforms.
Draw the full-wave voltage doubler circuit diagram. When a 1:4 transformer is used in this circuit andIf Vo=12sin(314t) alternative signal is obtained at the output, the frequency of the input signal, maximum and rmsCalculate its value.
1. Single phase half-wave converter has a purely resistive load of R and delay angle is a= n/2 determine: (a) Rectification efficiency (b) Form factor (c) Ripple factor.
a. Design an RC circuit to provide three leading phase shifts with ±2 % tolerance (30, 90, and 180 degree) of the output voltage relative to the input voltage . The input voltage is represented by the transformer secondary voltage. b. Design an RL circuit to provide thr ee lagging phase shifts with ±2 % tolerance (40, 60, and 120 degree) of the output voltage relative to the input voltage. The input voltage is represented by the same transformer secondary voltage.
A single phase full converter feeds power to RLE load with R=10 ohm, L=10 mH and E=50 V, the ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 600 ?
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
An AC source provides peak output Vi and peak current ii when connected to the coil primary of a transformer. The transformer has Np turns in the primary coil and Ns turns in the secondary coil. A resistance circuit R is connected to the transformer, see figure below. What is the equivalent resistance of the circuit?
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
2. The circuit given below is using a transformer of 230V/30V. The load resistance is 10KS. Find Vin (rms and peak values), Vdiode and VLOAD (Peak and dc values). Draw the input and output voltage waveforms. (Si diode) Vin: Vin rms= Vin peak = VDIODE Vdiode = 4 Vin VLOAD: VLOAD Peak =. Load VLOAD VLOAD DC= 2031 Supply wwwwww
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS