For the piping system shown below, determine the flow distribution and the piezometric heads at the junction (j) using the Hardy -Cross Method of solution. Power = 20 Kw D= 0.2 m, D,= 0.15 m, D= 0.15 m f,= 0.021, f- 0.018, f, = 0.023 L2=180 30 m L3=385 B L1=135 2 15 m |10 m A 3 Pump 1

For the piping system shown below, determine the flow distribution and the piezometric heads at the junction (j) using the Hardy -Cross Method of solution. Power = 20 Kw D= 0.2 m, D,= 0.15 m, D= 0.15 m f,= 0.021, f- 0.018, f, = 0.023 L2=180 30 m L3=385 B L1=135 2 15 m |10 m A 3 Pump 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question: The pressure pipe elbow with 30 degree orientation in the vertical plane is 60 cm in…

A: Solution

Q: 8- For the system in figure below, each pipe is 250mm diameter ,1000m length and f=0.015, discharge…

A: For calculating discharge in branched pipes, it is important to know the height of the junction…

Q: : For the system shown below: 1-Find the water power of the turbine (PT) if the required power…

Q: a sump to an overhead reservoir. The static lift is 40 m out of which 3 m is the suction lift. The…

Q: power output of the motor?

Q: Water is drawn into the pump, such that the pressure at ne inlet A is -25 kPa and the pressure at B…

A: Given data :Pressure at point A and B is PA=-25kPA, PB=160kPaDischarge Q=0.08cumech=2m

Q: without rupturing. Determine the maximum length, 1, allowed if the roughn 00015 ft and the flowrate…

Q: In the figure, suppose that 0= 30°, V₁ = 100 ft/s and the stream is a jet of water with an initial…

A: Given:- θ=30oV1=100 ft/sInitial diameter of jet of water=2 inV2=90 ft/s To find:- (a) The flow rate…

Q: Water at 70°F passes through 0.75-in-internal diameter copper tubes at a rate of 0.4 lbm/s.…

Q: Oil with a sp.gr. of 0.86 is being pumped from a reservoir shown. The pressures at the points 1 and…

Q: Reservoir, pipe and turbine A cylindrycal tankof radiu Ra contains water. It is connected by a pipe…

A: Q = 1 L/s or 0.001 m3/s Rb = 8 cm or 0.08 m Rc= 4 cm or 0.04 m h0=1.50m L = 10m Kinematic…

Q: Q.2. For the pipe network shown in the figure below, find the diameter of pipe (DC) if the head…

A: L = 500 m CHW = 100

Q: AcylinuTIcal laiiK Tlavilng a uldilitit UI ZII and height of 4m is open at one end and closed at the…

A: γw=9.81 KN/m3

Q: A pump delivers water at a flow of 10 cubic feet per second (cfs) from a lower reservoir to an upper…

A: Discharge Q=10 ft3/s=0.283168 m3/sec diameter d=16 in=1.33 ftarea A=π4×d2=π4×16122=1.396 ft2…

Q: The Power (P) required to drive the pump depends upon the diameter (D), the angular velocity (0),…

Q: Find the time it takes to decrease the water level in the tank 1 by 1.5m. Use C = 0.60 h.l. 2.3m do:…

A: Given data: diameter of tank 1 D1=6m Dimensions of tank 2 are 3m x 2m Difference in water level h=…

Q: In the supply system (Q=0.89cfs) shown in the figure, the pressure required at the delivery end is…

A: Q = 0.89 cfs Diameter = 4 in = 0.333 ft Length = 1000 ft Pressure at delivery end = 65 psi Water…

Q: The centrifugal pump blades are 20 mm in depth at the outlet. The impeller is 250 mm in diameter and…

A: A centrifugal pump's impeller features backward-facing blades that are angled at 30 degrees to the…

Q: Water flows in a steel pipe (ɛ = 0.00020 feet) at a flow Q = 12.5 cfs. The diameter of the pipe is D…

A: Given that: Surface roughness, ∈=0.00020 ftDischarge, Q=12.5 cfsDiameter…

Q: pump is to deliver water from an underground tank against a static head of 40m. The suction pipe 50m…

Q: In Fig. all pipes are 8-cm-diameter cast iron. Determine the flow rate from reservoir (1) if valve C…

A: D = 8 cm or 0.08 m Kv = 0.5

Q: L For the figure shown, determine the elevation at c. Use Darcy-Weisbach formula to compute for the…

Q: D washer (2) n holes of diameter D. To reduce water consumption, a washer is installed in the shower…

A: Velocity in the pipe without reducer at section 1 and at the outlet (considering it as 2):…

Q: El. 200 mA A Res. H-W Pipe B Pipe E pipec → Negleet minor losses → Pipes B, C, and E are all have: L…

A: Vc = 5m/s

Q: An 8 hp pump is installed near the reservoir container of oil having a s.g. Of 0.82. The rate of…

Q: A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at point %3D 1 and 2…

Q: SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in…

Q: Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in…

A: ##Calculation of diameter of Pipe 2 using hazen Williams equation

Q: Q3: A: In figure (3), the flow rate of water from reservoir (A) is 0.438 m³/s. Determine the power…

A: ZA = 123m ZB = 122m ZE = 80m C = (8g/f)0.5 or, f = 8g/C2 = 8*9.81/1202 = 0.0055 V1 = Q/A1 =

Q: // Find the total head loss of water moving in the pipe shown in figure below. The pipe is…

Q: 4) Two tanks of liquid with v-1.02x10-6 ms are connected by two pipes in series as show in the…

A: Given: D1=0.305mD2=0.610mL1=610mL2=9140mE=0.0030ma=0.0566 m3/s To find: H

Q: For the arrangement shown below, find the discharge in each pipe in li/sec using a friction factor f…

A: Head loss remains same in parallel pipes.

Q: Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow…

Q: 2. The rotor of a centrifugal pump is 170 mm in diameter and runs at 1450 rpm. It has a depth of 15…

Q: The fluid in the tank is water. Flow is steady state, incompressible and nonviscid. It is known that…

A: Using the Bernoulli's equation between the tank and the point 1 - Patmρg + v122g + Z1 = P1ρg +…

Q: Situation 1 The 60 cm pipe conducts water from reservoir A to a pressure turbine which discharges…

Q: 3) Given: Q = 14 lit/sec; For the suction pipe: diam. = 180mm with head loss = three times its %3D…

Q: ELEV. 130m 2 B L = 1000m D = 200mm f = 0.023 L = 1500m D = 250mm L = 300m ELEV. = 40m f = 0.02 D =…

Q: The 600 mm pipe shown conducts water from reservoir A to a pressure turbine, which discharges…

A: Head lost from A to 1 = 5 x velocity head in pipeHead lost from 2 to B = 0.2 x velocity head in…

Q: In the following system, the flow rate of Q = 400 It / s is transmitted from the A chamber to the B…

A: The liquid from one chamber to another chamber due to variation in height and pressure…

Q: Consider the section of water distribution piping shown below. Ignoring minor losses, find the flow…

A: From the above figure the given values are as follows,EA=141mZA=60mA-B:-3000m@400mmC=120…

Q: In the figure the water (P = 1000 kg/m3) enters the pump to be raised at (1), with a pressure P1 =…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

For the piping system shown below, determine the flow distribution and the piezometric
heads at the junction (j) using the Hardy-Cross Method of solution. Power = 20 Kw
D= 0.2 m,
D,= 0.15 m,
D= 0.15 m
f,= 0.021,
f= 0.018,
f, = 0.023
L2=180
30 m
L3=385
B
L1=135
2
15 m
| 10 m
A
3
Pump
1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water is taken from a large reservoir by means of a pipe as shown below. The turbine extracts 10 m of head from the system and water discharges out at point B. The head loss in the pipe is formulized as; 2*(V^2)/2g, where V is the average velocity in the pipe. Determine the discharge in the system Determine the turbine power if n= 0.8. Plot EGL and HGL of the system. a) b) c) 40 m INTLUID MILLTANICO IvanichiuISTIR TARGITEST TEGE D- 0.1 m B DES DElidi 15 m
please use a=7 , b=2
help with hw...thnks
The 24-in. pipe conducts water from reservoir A to a pressure turbine, which discharges through another 24-in. pipe into tailrace B. The loss of head from A to 1 is 5 times the velocity head in the pipe and the loss of head from 2 to B is 0.2 times the velocity head in the pipe. If the discharge is 25 cfs, (a) What is the head extracted, he, (ft) by the turbine? (b) What horsepower is being given up by the water to the turbine? El 200 ft El 15 ft 24-in. pipe El O ft 24-in pipe
Situation 1 The 60 cm pipe conducts water from reservoir A to a pressure turbine which discharges through another 60 cm pipe into tailrace B. -CL 70 m The head losses are: From A-1 : From 2-B : 0.2 Heo cm g If the discharge is 0.70 m3 /sec: HEL Dn 1. Determine the head extracted by the turbine (HE) in meters. DATUM E 2. Solve for the input power of the turbine (Pinput or Pturbine) in kW. TURBINE 3. At 90% efficiency, compute for the output power (Poutput) for electricity in kW. Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m/s. 1 Pipe Length Diameter Friction Factor 1,800 mm 1,500 mm 2,000 mm 0.020 0.018 0.022 400 mm A 2 в у 350 mm 3 300 mm 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
Patm = 10^5, P(water) = 1000 kg/m^3 ; Pair = 1.2 kg/m^3 ; g = 9.8m/s^2gage pressure Pg = P - Patm
-8.33 -0.12 8.33 (1) 0.12 -L Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. h (2) e - - - -
For the piping system shown below, determine the flow distribution and the piezometric = 20 Kw heads at the junction (j) using the Newton-Raphson Method of solution, power = 0.15 m D,= 0.2 m, D,= 0.15 m, %3D 2. f=0.021, f= 0.018, f,= 0.023 L2=140 30 m B L3=345 L1=95 2 15 m |10 m A Pump 1
A steam function is given by: 4 = 2x²y + (x + 1)y² The flow rate across a line joining points A (3, 0) and B (0, 2) is
Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is 50 LPM, find the NPSH available immediately before the pump. The length of the pipe from the reservoir to the pump is 13.1 meters, and its diameter is 2.8 cm. The distance is h2=6.8 m. Assume a friction factor of 0.021. The vapor pressure of water at the current temperature is 2,399 Pa. Current atmospheric pressure is 95,194 Pa. The density of water is 991 kg/m^3
Answer fast
At night, water is pumped from a treatment plant reservoir through distributing piping to an elevated storage tank. Assume no other withdrawals from the system. The water surface in the supply reservoir is at 3m elevation, the lift pump elevation is 6m, the water elevation in the elevated tank is 42m. The pipe network maybe considered equivalent to 1500m of 250mm diameter. Use C=100. There is a supply of 60 Liters/sec. to the tank. a. Compute the head loss of the 250mm diameter pipe. b. Compute the pump discharge pressure required to supply a flow of 60L/s to the tank, c. Compute the slope of the energy gradient