For the arrangement shown below, find the discharge in each pipe in li/sec using a friction factor f = 0.02 for all pipes. The head loss from pipe 1 to pipe 5 is 20m. L=700m D=600mm 5 Q5 L=600m L=700m D=500mm D=600mm L=500m L=600m D=400mm D=400mm ANSWER: Q1 = Q5 = 27.6 li/sec Q2 = 21.4 li/sec %3D Q3 = 6.2 li/sec Q4 = 6.2 li/sec

For the arrangement shown below, find the discharge in each pipe in li/sec using a friction factor f = 0.02 for all pipes. The head loss from pipe 1 to pipe 5 is 20m. L=700m D=600mm 5 Q5 L=600m L=700m D=500mm D=600mm L=500m L=600m D=400mm D=400mm ANSWER: Q1 = Q5 = 27.6 li/sec Q2 = 21.4 li/sec %3D Q3 = 6.2 li/sec Q4 = 6.2 li/sec

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hydraulic Toolbox 3
A commercial steel pipe—with a diameter, D, of 200 mm and length, L, of 30 m—is used to drain oil (S.G.=0.8)tank. Determine the discharge, in liters per second, when the oil level in the tank is 3 m above the exit of the pipe.Neglect component or minor losses and quantify the friction losses using the Darcy-Weisbach equation shownbelow, use friction factor, f, of 0.12.
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
Read the question carefully and give me right solution according to the question
Two pipes A and B are connected in parallel between two points M and N as shown in figure. Pipe A is 80 mm diameter, 900 m long and its friction factor is 0.015. Pipe B is of 100 mm diameter, 700 m long and its friction factor is 0.018. A total discharge of 0.030 m³/s is entering the parallel pipes through the division at M. Calculate the discharge in the two pipes A and B. M = 0.015 A fA 80 mm dia, 900 m 100 mm dia, 700 m B fB = = 0.018 N
Question 4: H₂=4 m f=0.15 D₁ = 50 mm H₁ 4 m 25 m L = 100 m A. Two tanks A and B were connected by a 50 mm-diameter pipe (f=0.15) that is 100 m in length. Calculate the total flow between the two tanks. B. A pipe of 200mm diameter (f-0.01) and length X is to be connected in series to replace X length of the 50mm pipe. If the purpose is to increase flow by 50%. Find Length X. ***** La=X f=0.01 D. = 200 mm
Plz write neat
uservoir discharges into a 55-inch pipe that discharges freely, as shown below. What is the pressure in the pipe at point A? Consider friction. Use f =0.02 Elev 155 ft Inv. @ A 134.2 ft 55 in 140 ft Inv. 120 ft 420 ft 900 ft 1450 ft a. 502 psf b. 502 psi c. 457 psf d. 457 psi e. 36 ft ,what is the velocity at point B? a. 17.5 fps b. 36 fps c. 3.6 fps d. 4.57 fps e. 50.2 fps ar
I need help for this question. Thank youu
a=4 b=0 C=1
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
In the figure shown, solve for the theoretical velocity of the jet, theactual velocity and the discharge through the orifice considering thefollowing:a) p1 = p2 = 0 Cc = 1.00 (rounded)h = 5 m of oil Cv = 0.97Do = 5 cmb) p1 = p2 = 0 Cc = 0.62 (sharp-edged)h = 5 m of water Cv = 0.98Do = 5 cmc) p1 = 70 kPa C = Cv = 0.95 (rounded)p2 = 0 Do = 7.5 cmh = 1.60 m (liquid with sp. gr. = 3)