3) Given: Q = 14 lit/sec; For the suction pipe: diam. = 180mm with head loss = three times its %3D %3D velocity head; For the discharge pie: diam. = 142mm with head loss of twenty times its velocity head; pump elev. = 55m. Req'd: a) horsepower input of the pump if Efficiency = 88% b) pressure at the discharge side of the pump. EL 109 m EL. 55 m A EL 54 m RIVER 8

3) Given: Q = 14 lit/sec; For the suction pipe: diam. = 180mm with head loss = three times its %3D %3D velocity head; For the discharge pie: diam. = 142mm with head loss of twenty times its velocity head; pump elev. = 55m. Req'd: a) horsepower input of the pump if Efficiency = 88% b) pressure at the discharge side of the pump. EL 109 m EL. 55 m A EL 54 m RIVER 8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(CLO1/ELO1, 2 min) [2] (3] Find the value of a (m3/s) in pipe 2. If the pump characteristic curve is known Hp = 90 – 1002 ; The elevations of A, B and C are 20m, 40m and 45m, respectively; Pipe L(m) D(m) f K 125 0.35 0.03 2 150 0.2 0.02 3. 500 0.2 0.03 1 4 600 0.2 0.02 400 0.25 0.02 2 Select one: a. 0.15 b. 0.30 c. 0. 34 d. 0.25 e. 0.20
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
PROBLEM: The discharge of the pipe system shown is 420 liters/sec, Deter- mine the head loss from A to D. Assume f = 0.020 30mmo; GOO m 750 mmo; 900 250 mm d; 450 m GOo mm 6; 1200m 3 Solution 375 mma; 750 m 0 0826 10
Example 6 Prove that if Q, represents normal discharge at a particular depth 'y' and Q. represents the critical discharge at same depth 'y' then. dy 1-(Q/Q So dx 1-(Q/Q
A pump is used to draw water from an open reservoir to an open tank on thetop of a building. The discharge flow rate is 50 lps. The static suction head of the pump is6 m and the static discharge head is 20 m. The cast iron, schedule 40, pipe in the suctionline is 4 inches nominal diameter and 20 m long. The cast iron, schedule 40, pipe in thedischarge line is 6 inches nominal diameter and 65 m long. The fittings and valvesinstalled in the suction line are the following: two 90o standard elbow and one gate valve.For the discharge line, are the following: one check valve, one gate valve, and three 90ostandard elbows. Assuming a water viscosity of 0.001002 Pa-s, and a pump efficiency of82 %. Determine: a) the total dynamic head b) the pump brake power. Show the neat schematic diagram of pumping system. Note: Use Moody’s equation for the value of friction factor; and table for determining the equivalent length of the components.
3)a: For the figure below, find the discharge in pipe, neglect the minor losses only. (e-0.001m, D-Im, L-600m, u-1.307*10 m/sec). LAS 5m 2 1.96 D. b: In a pipe of 300 mm diameter the maximum velocity of the flow is found to be 2 m/s. If the flow in the pipe is laminar, determine: 1) The average velocity and the radius at which having the same velocity magnitude as the average velocity. 2) The velocity at 50 mm from the wall of the pipe. 5964 11.62
Situation 1: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. EI. 240m B El. Om 100mm A O 150mm El. -20m 2. Find the power delivered by the pump in kW. 3. Calculate the pressure head at point 1 in meters. 4. Solve the pressure head at point 2 in meters.
Given:Q = 28 lit/sKc = 0.40Kb = 0.5Ke = 0.40Pipe diam = 10 cmFriction factor = 0.037 1.) From the given data of Figure 1: a) Calculate the value of H. b) If a straight pipe is used from A to B, determine the new value of the discharge in lit/sec.
12. Find the discharge in each link using the given initial distribution by making 2 iterations and pressure drop between points O and C if they have the same elevation. B A 5 lt/min 5 7 lt/min с ? It/min 5 lt/min 20 D E KBC KCD-KAO-KOE KAB=KDE Koc=3KBC KAB=2KBC Koc=30 min²/dm5
Design Characteristics Binch Sch 40 Steel Pips hug ht Twenty feet) 90⁰ 7 a pump 20 for Standard elbow and The spraty System the various pump shown below Hinch sch 40 steel pipys Pipa ↓ B Рв=норвід ioft Flowrate=1759pm Length of Suction line = 25ft Lingth of discharge line = бодн Determine the NPSHR ? show calculations
5. ol with sp. gr. of 0.88 is being pumped frem a lower reservolr to an elevated tank The pump In the system is 65% efflelent and Is rated at 160kW. Determine the flow rate of the oll in the pipe if the total head los (rom point 1 to point 2 is 5.5m of oll. 150m 200-mm Pump Elev 160m Elev. 150 m
3. The flow form A to I is 300 L/s. Using the following data compute the discharge in each pipe Use conventional solution. 7 C 1 D 3 نيا B 5 2 E 6 F .8 G H 9 10 I Pipe AB BE BC BD DF FE CH EG HG GI n 0.012 0.011 0.013 0.014 0.014 0.014 0.013 0.011 0.011 0.012 Diameter (mm) 450 360 300 200 250 200 350 250 300 450 Length in (m) 300 360 370 150 300 150 660 300 370 600