i)Calculate the flow rate through the system. shows a cross-section through a structure (marked A) that transitionswater from a 2 m wide rectangular channel with flow depth y = 4 m to a pipe with diameter D = 1 mat B. The friction loss through the transition is described by the equation h₁ = 0.3%, where vg is thevelocity in the pipe at B. A pressure gauge at the bottom of the pipe B gives a reading of 10 kPa.Assume a hydrostatic pressure distribution between the top and bottom of the pipe at B.yABD→

Answer We can use Bernoulli's energy equation to calculate the flow rate through the system Consider…

Answered: Calculate the flow rate through the…

Engineering

Civil Engineering

Calculate the flow rate through the system

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the pipe network next if: QA=250 Vs QB - 250 1/s QC - 150 l/s QD = 100 ls Length Diameter Pipe…

A: THE QUESTION IS BEING SOLVED BY HARDY CROSS METHOD SO, YOU NEED TO PERFORM FURTHUR TRIAL AND ERROR…

Q: Water at 4°C flows through a 5-inch ID smooth pipe. The Reynolds number of the flow is 450000.…

A: Re = 450000 temp = 4° It has been asked in the question to calculate ratio of maximum velocity to…

Q: What is Venturi meter? Derive an expression for discharge through venturi meter.

A: Vortex flow is defined as the flow of a fluid along a curved path or the flow of a rotating mass of…

Q: Compute the discharge through a 1000 mm diameter pipe flowing at an velocity of 1.5 m/s.

A: Given: Diameter of pipe, d = 1000 mm Velocity, v = 1.5 m/s

Q: Problem 4. (15pts) An unknow fluid has a specific gravity of 1.25 and viscosity of 5x10-³Ns/m².…

A: The objective of the question is to determine the kinematic viscosity of an unknown fluid given its…

Q: Answer within 3-5 sentences only. 1. What is the purpose of a Venturi meter? 2. What is a hydraulics…

Q: Dutflow is not equal to the value of q in volume per time unit. O True D False

A: Given data in question Outflow Discharge q To find out True or false

Q: Situation 2: VWater drops from a faucet at the rate of 5 drops per second. h2 hi S B

A: A faucet is a device designed to control the flow of liquid or gas from a conduit or container.…

Q: Derive a relation for mass flow rate for variable head meters for compressible fluids.

Q: A venturi meter reduces the pipe dia. from 10 cm. to 5 cm. Calculate the flow rate and mass flow…

A: diameter of inletD1=10 cmdiameter of throatD2=5 cmtherefore,A1=π4102A1=25π cm2andA2=π452A2=6.25π…

Q: A city requires a flow of 30 MGD (million gallons per day) for its water supply. Compute the…

A: V=6ft/s Q=30MGD

Q: State the causes of flow changes for the following fluid flow by your understanding with…

A: Causes of flow changes from Laminar to Turbulent : Flow patterns can be characterized as laminar or…

Q: Water at 20°C flows through a 3 cm ID smooth brass tube at a rate of 0.002 m³/s. What is f for this…

A: Given :

Q: 2. A pipe carries water at a flow rate of 90 L/s. Determine the minimum inside diameter so that the…

A: Given, Q= 90 l/s =90x 10-3 m3/s Q= 9x10-2 m3/s

Q: 5. The flow of fluid along curvilinear or curved path is known as a) Curvilinear Flow b) Circular…

Q: 18. Water flows through a horizontal Venturi meter having an inlet diameter of 30 cm and throat of…

A: 18. Water flows through a horizontal Venturi meter with an inlet diameter of 30 cm and throat…

Q: ) Draw the flow pattern of laminar flow around a cylinder with turbulent flow separation.

Q: A liquid flow through pipe of diameter 10 cm a velocity of 6 cm Find the value of discharge

Q: pipeline between point A and B consists of 1000 ft of 18in followed by 800 ft of 12in…

Q: 1-steady flow 2-flow patterns and flow visualisation 3-streanlines 4-strean tubes 5-pathlines…

A: 1-steady flow- its a flow in which the fluid properties is remain constant with respect to time…

Q: 13. Which of the following is correct? a) There will be no flow across the streamtube b) There will…

A: Option A is correct There will be no flow across the stream tube.

Q: flow is having the same parameters

A: To find : What it will be called If a flow is having the same parameters at any given point.

Q: Question 15 The flow rate in a pipe with 750mm diameter is 500 Liters per second. The fluid is water…

Q: 3. Determine the discharge of water through the 50-cm steel (Wrought iron) pipe shown in the figure…

A: Given that : Diameter of steel pipe = 50 cm Determine the discharge of water through 50 cm steel…

Q: Q2. Air having a specific weight of 0.0795 lb/ft³ flows into the duct at A with an average velocity…

Q: 1. A horizontal pipeline reduces from 190 mm diameter to 70 mm diameter. Water enters the pipe at…

Q: Assume water flow through a pipe with two sections. Assume the diameter is 6 and 9inches. The…

Q: Q2/ Statement: "The Equations of Two Phase Flow can be derived easily simply by using Material…

A: Material balance and Darcy's law can be used to create a two-dimensional flow equation: The term…

Q: . Water flows through a horizontal Venturi meter having an inlet diameter of 30 cm and throat of 17…

Q: Discuss the importance of the proper selection of tubing, fitting, and hose installation in a…

A: It is very important to select the correct tubing, fitting and hose installation in a hydraulic…

Q: A cylindrical tank 10 ft. high and 4 ft in diameter placed so that its axis is horizontal. It is…

Q: A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of…

A: Given Flow discharge (Q)= 4.6 cfs Diameter at section 1 (D1)=12''=1ft Diameter at section 2…

Q: What makes the density of water from different sources differ?

Q: Compute the flow rate at water depth "y" = your Roll No (FPS system) %3D 0.025

A: GIVEN DATA Let us assume the depth as y=10ft (y=YOUR ROLL NO) n=0.025, so=0.002, calculate the…

Q: Q3. Compute volumetric flow rates in each pipe for the given data: Pipe Li (m) Di (cm) Ei (mm) 1 800…

A: Solution;

Concept explainers

Pressure and Stress

Question

i)Calculate the flow rate through the system.

shows a cross-section through a structure (marked A) that transitions
water from a 2 m wide rectangular channel with flow depth y = 4 m to a pipe with diameter D = 1 m
at B. The friction loss through the transition is described by the equation h₁ = 0.3%, where vg is the
velocity in the pipe at B. A pressure gauge at the bottom of the pipe B gives a reading of 10 kPa.
Assume a hydrostatic pressure distribution between the top and bottom of the pipe at B.
y
A
B
D→

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water at 50°F flows at a rate of 4 ft/s in the space between 6-in Schedule 40 steel pipe and a square duct with inside dimensions of 10 in. The shape of the duct is Figure below. Compute the Reynolds number to determine if the flow is laminar or turbulent. 10 in. 6 in. diainler
Question 4 Determine the size of the control valve required to control the flow rate of water. The maximum flow rate is 850 gal/min, and the available pressure drop across the valve is 50 psi. Allow a safety factor of at least 30%.
Water flows at a velocity of 10 m / s through a 90 mm radius pipe. a. Calculate and state what the flow regime is under these conditions. b. In order for the water flowing from the same pipe to be suitable for the transition regime and turbulent regime, the flow Calculate what / what the speed value range might be.
Determine the energy loss due to a sudden enlargement from a standard DN 25 Schedule 80 steel pipe to a DN 90 mm Schedule 80 steel pipe when the rate of flow is 3 x 10-3 m³/s.
Hydrology 1. Discuss the streamflow measurement through flowrate (discharge) and velocity
. A proposed elevated tank for a certain community has a diameter of 72 inches and a height of 8.930 feet. It is to draw water by a pump from an aquifer down below the ground. Two steel hoops, 24.4 in2 in cross section, are installed around the tank, one at the bottom and one at the top, to prevent the bursting of the tank by the water pressure inside. (Use unit weight of water, water = 62.4 lb/ft3 ) a) Compute the internal stress at the bottom of the tank (in psf). b) Determine the tensile stress at the top (in psi). c) Determine the tensile stress at the bottom (in psi).
I need the answer as soon as possible
I need the answer as soon as possible
Water flows through a one-inch diameter pipe at a velocity of 14.4 ft/s. The pipe divides into two 3/4-pipes. Find the flow rate in the two 3/4-inch pipes.
A fluid enters a 3" diameter pipe; the Reynolds number for the flow is 72,671. At what distance from the pipe entrance does the flow become fully developed (ie. determine the entrance length for the flow). Answer in feet and include 1 digit after the decimal place.