The pipe assembly is subjected to the action of a wrench at B and a couple at A. (Figure 1) Simplify this system to a resultant wrench. Set F = 40 N. a) Determine the components of the resultant force of the wrench. Enter the x, y, and z components of the force separated by commas. Express your answers in newtons to three significant figures. b) Determine the components of the resultant moment of the wrench. Enter the x, y, and z components of the moment separated by commas. Express your answer in newton-meters to three significant figures. c) Specify the location of the wrench along the axis of pipe CD��, measured from point C�. Express your answer to three significant figures and include the appropriate units.

The pipe assembly is subjected to the action of a wrench at B and a couple at A. (Figure 1) Simplify this system to a resultant wrench. Set F = 40 N. a) Determine the components of the resultant force of the wrench. Enter the x, y, and z components of the force separated by commas. Express your answers in newtons to three significant figures. b) Determine the components of the resultant moment of the wrench. Enter the x, y, and z components of the moment separated by commas. Express your answer in newton-meters to three significant figures. c) Specify the location of the wrench along the axis of pipe CD��, measured from point C�. Express your answer to three significant figures and include the appropriate units.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

Calculate -3 T -6 Answer: 10 ft -3 ft 10 ft -3 ft a dx. a, ft/sec² 19 a dx = 0 0 i x, ft 14.31 5 1 1 7 10 ft²/sec²
b) A sedan car weights 2100 kg with 45:55 distributions front to rear. The car has wheelbase of 1.9 m. With aid of following table showing the tyre cornering stiffness values for different loads: Load Cornering Stiffness (kg/deg) 300 131 400 149 500 174 600 203 i) Calculate the cornering coefficient for the front and rear tyres. ii) Calculate the understeering gradient. iii) Determine whether it is understeer or over steer. iv) Calculate critical or characteristic speed.
Parts for each product Homework 1 n produce dryer plant Can for each product castiens Then each product is assembled in its dedicated washing and dryer A machines. Difterent are manufactured by press and motor ly sechon. The the monthly capacity of different sections are: washing machine or looo dryer machine Press section: 100 - Motor section: 1600 washing machine or 7o00 drjer machine machine assembly line: goo0 machine washing druer machine assembly line: 5000 machine washing 1, profit for each unct of washing and dryer machines is 270 and 300 respectively. Formulate a linear programming problem for Find ing how many washing and dryer machines should be produced many washing to maximize total plant's profit. 2.A A Post Company need to transfer 30000 boxes with two each truck presented of olifferent trucks. Chavactenistics problem for The table below. Formulate a linear programming each truck to optimum nunber of minimIze total Cost.
A resurfaced fl oor costs $5000 and will last 2 years. If money is worth 10 percent aftertaxes, how long must a new fl oor costing $19,000 last to be economically justifi ed? Thetax rate is 52 percent. For tax purposes a new fl oor can be written off in 1 year. Use sumof-the-years-digits depreciation. Use the capitalized cost method for your analysis.
F=540 F 10.5 m 1,5 m 3 m 4 m 1) Find Fx N 2) Fy F 2 %3D
Q2-Indicate the balances you would write and the order in which you would write them to solve for the unknown stream variables in the following process: m(e/s) 400 g/s 0.3 g A/g 0.2 g B/g 0.5 g C/g xtg A/g) 0.1 g B/g (0.9-xXg C/g) m2(g A/s)
Over the outside part of the room window, the wind is blowing with a speed of 10 m/sec. Due to this wind motion, the temperature on the outer surface of the window is 5 degrees lower than the room temperature. Determine the convective heat flux if the wind temperature is 10 C with a heat transfer coefficient of 10 W/(mK). Accept the temperature inside the room as 25 C. A) 200 W B) 100 W C) 200 W/(m^2) D) 100 W/(m^2) E) Not sufficient information
%EV l. O 9:Y) äbäi 15 Q4The Trigonometric functions for the fig. below are B. b. D) cos A=a/c, tan A= a/b, sin A= c/a O B) cos A=b/c, tan A= a/b, sin A= c/a A) cos B=a/c, tan B= a/b, sin B= c/a O C) cos B=b/c, tan B= a/b, sin B= a/c O صفحة 1 من 1 إرسال عدم إرسال كلمات المرور عبر نماذج Go ogle مطلقا. لم يتم إنشاء هذا المحتوى ولا اعتماده من قبل Go ogle. الإبلاغ عن إساءة الاستخدام - شروط الخدمة - بسياسة الخصوصية Google zilaj II
Problem 3 A small spherical ball having diameter of d= 20 cm and at temperature of 150 °C is placed in a water bath maintained at 20 °C to be cooled down. Consider the proportionality constant to be a= 0.005/m²-s. a) Determine the time required for the temperature of the ball to reach 40 °C. b) At what time the temperature of the ball reach to 20 °C? c) What's the final temperature of the ball? Bulk environmental temperature = T, Surface area, A-7 T(t) Initial solid temperature, T
1- Select the optimum choice for: high speed air craft skins material. Table 1: The properties of metallic materials E, GPa Max. use lemp, 'C | Density, Mg/cm' ay, MPa | Relative cost per unit sheet area Material 2.8 300 2 Aluminum alloy 200 69 200 7,8 350 350 700 Carbon steel Stainless steel 193 7.8 650 6 8.9 600 6 Nickel alloy Titanium alloy 207 1000 116 600 4.5 900 10 Table 2: Weighting factor Specific yield strength: Max, use temperature: Youngs modulus: 4 2
10 show complete STEP BY STEP solution, and draw a FBD.
A water cooler uses 100 lb/hr of melting ice (32 deg F) to cool running water from 80 deg F to 42deg F. Based on the inside coil area, Ui= 110 BTU/hr- sq FT deg F, find: a) LMTD; b) Inside surface areac) GPM of water cooled please draw the diagram