1) A stepladder is constructed as shown in the figure. Thetotal mass of the ladder is 10 kg (each side has a mass of 5kg). There is no friction between the ladder and the floor.a. What is the tension in the chain?b.What is the magnitude of the force exerted by thehinge on one side of the ladder?Hinge-ChainCG0.50mUniform board(CG at center)1.10 m1.30m

To determine the tension in the chain and magnitude of the force exerted by the hinge and given the…

Answered: a. What is the tension in the chain? b.…

a. What is the tension in the chain? b. What is the magnitude of the force exerted by the hinge on one side of the ladder?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. A ladder of length 12 m leaning up against a wall makes a 50 degree angle with the ground. The top of the ladder has sliders so that it can slide up and down the wall. Therefore, consider the top of the ladder to be frictionless. The ladder has a weight of 189 N that acts at its center. Someone weighing Fg = 1000 N is 0.92 m vertically below B, but on the ladder. Another person is on the ground holding the ladder by pushing on it horizontally with a force F. If the coefficient of static friction is 0.32, find the horizontal force F that must be applied at a vertical height of 1.2 m to prevent the ladder from slipping. LL F 1.2 m 12 m 50⁰ Fg B .92 m
A uniform horizontal strut weighs 370.0 N. One end of the strut is attached to a hinged support at the wall, and the other end of the strut is attached to a sign that weighs 170.0 N. The strut is also supported by a cable attached between the end of the strut and the wall. Assume that the entire weight of the sign is attached at the very end of the strut. 30° Restaurant Find the tension in the cable (in N). Find the force (in N) at the hinge of the strut. (Give the direction in degrees counterclockwise from the +x-axis. Assume that the +x-axis is to the right.) magnitude direction °counterclockwise from the +x-axis
1. This arm is attached to a wall on the left. The right end is free hanging. Each section is 1.9m wide and 3.6m high. If the force at the end of the arm is F = 170.0N, what is the force in member 2? Use a positive number if it is in tension and a negative number if it is in compression. 2. This arm is attached to a wall on the left. The right end is free hanging. Each section is 1.2m wide and 3.0m high. If the force at the end of the arm is F = 150.0N, what is the force in member 9? Use a positive number if it is in tension and a negative number if it is in compression.
4. A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping. Draw the FBD
Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
3. The figure shows a 100.kg box suspended from the extreme side of the horizontal truss. Assume that the truss's weight is negligible; what is the tension (N) in the cord supporting the truss. Angle is 38 degrees from the horizontal side of the truss IS CORD truss 4. A 3,000. kg truck is towed up along a hill with a cord whose functional strength is 10,000 N. The hill is inclined at 15 degree from the horizontal. Find the maximum acceleration of the truck in m/s^2.
Q2): Body A is weight 100 N and tied to a rigid wall using a steel cable and it is located on body B of weight 300 N which rest on a rough surface (coefficient of fraction is 0,3). If the fraction coefficient between body A and B is equal to 0.25 and the pulling force P= 600 N. calculate the tension force of the steel cable. A 530 37 B TTTTTT
DETERMINE THE MEMBER FORCE AD (KN) SHOWN IN THE FIGURE.
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
4 A ski resort chair lift has towers spaced 38 m horizontaly appart. The upper tower is 15 m higher than the previous tower. If the chairs are 12 m horizontally appart and the first chair is 5 m past the lower tower what is the tension on both ends of the cable? 1:37:01 Book The mass of each chair is 350 Kg and the height above the lower tower for each chair's attachment to the cable is 0.58537 m, 4 m, 9.4244 m. Lower Tower Cable Tension = Upper Tower Cable Tension = kN. KN.
The level of a common steelyard without hook connections weights 7kg and acts at 5cm to the left of the fulcrum. The hook which carries the load,weights 4kg and is also attached on the left-hand side of the fulcrum at a distance of 12cm.if graduation mark 72cm from the fulcrum reads 50kg. Find (a).the weight of rider (b). How far is the zero graduation from fulcrum (c).What is the movement of riderper kg of graduation?
Answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) An electrical worker stands in the bucket that hangs from a pin at end D of the boom of the cherry picker in Fig. 1. The worker and bucket together weigh a total of 300 lb. Between A and C the boom weighs 1.1 Įb/in., and between C and D it weighs 0.8 Jb/in. Assume that AC and CD are uniform beams. Determine the normal force, the transverse shear force, and the bending moment that act at cross section E, midway between A and B. В Eaxial Eshear Emoment Ib Ib Ib Ib in 50" 40" D 10"10 INDICATE WHETHER POSITIVE OR NEGATIVE |20° Bucket 60° Fig. 1 (a) “Bucket truck."