Determine (a) the bit rate and (b) the resolution in the sampling of a seismic signalwith dynamic range of 1 volt if the sampling rate is and we use an 8-bit A/Dconverter. (c) What is the maximum frequency that can be present in the resultingdigital seismic signal? (d) If this were to be a PCM system, calculate the minimumsystem bandwidth required.

We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Answered: Determine (a) the bit rate and (b) the…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

7. A device that generates and demodulates digital modulation signals, usuallyat audio frequencies is the __________.8. The __________ consists of a series of pulses of varying amplitude thatcorrespond directly to the amplitude of the modulating signal.
4. The information in an analog voltage waveform is to be transmitted over a PCM system with a F 0.2% accuracy (full scale). The analog waveform has a bandwidth of 200 Hz, and an amplitude range of -5 to +5 V. determine the following: - The minimum sampling rate needed. - The number of bits needed in each PCM word. - The minimum bit rate in the PCM signal. - The minimum channel bandwidth for transmission of this PCM signal.
explain the working of phase shift method of generating SSB signal.
. What are specifications of Digital modulation techniques?
An analog signal with a bandwidth of 4.2 MHz is to be converted into binary PCM and transmit- ted over a channel. The peak-signal quantizing noise ratio at the receiver output must be at least 55 dB. (a) If we assume that P=0 and that there is no ISI, what will be the word length and the number of quantizing steps needed? (b) What will be the equivalent bit rate? (c) What will be the channel null bandwidth required if rectangular pulse shapes are used?
The information in an analog waveform, whose maximum frequency fm-4000Hz, is to be transmitted using a 16-level PAM system. The quantization must not exceed #1% of the peak-to peak analog signal. (a) What is the minimum number of bits per sample or bits per PCM word that should be used in this system? (b) What is the minimum required sampling rate, and what is the resulting bit rate? (c) What is the 16-ary PAM symbol Transmission rate?
Aliasing is happening when Select one: a. The sampling frequency is lower than twice the cutoff frequency. b. The sampling frequency is higher than twice the signal highest frequency component. C. The sampling frequency is lower than twice the signal highest frequency component. d. The sampling frequency equals twice the signal highest frequency component. e. The sampling frequency is lower than the cutoff frequency.
A PCM system uses an uniform quantizer followed by a 8 bit encoder. The sampling frequency exceed Nyquest frequency by 70%. 1) Determine the bandwidth of message. B) Determine the signal to noise ratio when a sinusoidal signal has peak amplitude 5volt.
A. If the analog signal to be quantized is a sinusoidal waveform, that is, X (t) = 9.5 sin (2000 t) and if the bipolar quantized uses 8 bits, determine 1. Number of quantization level 2. Quantization step size or resolution, assuming that the signal range is from -12 to 12 volts. 3. The signal power to quantization noise power.
For the AM envelope shown in figure A13, Voltage -8 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 Time Calculate the maximum amplitude of Choose... modulating signal. Calculate Modulation index Choose...
What is the main feature in AM modulation , that is used to judge if the modulation is good or not ? Explain with examples .
What are different step in typical ASIC design flow.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS