What will be the minimum transmission bandwidth of a PCM system if the number of bits per sample is 8 and the maximum frequency of the analog signal is 4.5 kHz?

Q: The information in an analog signal voltage waveform is to be transmitted over a PCM system with an…

A: Given, Analog signal voltage waveform is to be transmitter over a PCM system. Accuracy is ∆2=±0.1%…

Q: An a differential pulse code modulated system, the transmitted bits per sample is 7.  How many…

A: number of quantization level given by 2nwhere n is no of bits

Q: What is the effect of over-modulation on the output signal? How one can avoid the over- modulation…

A: What is over-modulation? When the maximum level is reached, it is claimed that over-modulation takes…

Q: Explain the importance of brown-out detection in microcontroller systems.

A: Brown-out detection is a crucial feature in microcontroller systems that helps ensure the reliable…

Q: What does a binary digital signal consist of?

A:

Q: 7) If the analog signal has amplitudes that varies between-3 and 3 volts And maximum frequency of 10…

A: The given signal is shown below, Where,Amplitude range = -3 to +3 VMaximum frequency=10 kHzn=3 bits

Q: A. Draw the maximum point detector circuit and sketch the output waveform for the input signal of…

A:

Q: Which of the following will happen if the boron implantation is performed without the photoresist…

A: Aim:To choose the correct optionWhat will happen if the boron implantation is performed without the…

Q: 3. What are the three general classes of erroTS ?

A:

Q: 3. What happens if the inverting & non-inverting i/p of the comparator interchanged?

A: As per guidelines, we can only provide the solution of one question in multiple type of questions.…

Q: Using two pairs of emitters and detectors allows turning an incremental shaft encoder into an…

A: The answer is option 2 2. Usually the two emitter/detector pairs are out of phase by an angle of 90…

Q: What is the importance of the modulation percentage in an AM system, does it have to do with over…

A: The Amplitude Modulation (AM) is the process of varying high frequency carrier magnitude based on…

Q: What are some of the advantages of SAS versus SCSI?

A: The advantages of SAS over SCSI are given below---

Q: Suppose an analog-digital converter IC ('chip") inputs a voltage ranging from 0 to 3.5 volts DC and…

A: We need to find out the number of steps and step size for given analog to digital converter.

Q: What is AVR?

A: AVR is tends for Automatic Voltage Regulator. AVR is an electronic device which is used to maintain…

Q: Problem 2)- The figure below shows the binary input data and carrier signal that used in a optical…

A:

Q: Have a look at the problems that have surfaced because of the widespread use of digital materials.

A:

Q: What is the appropriate display type (common anode/common cathode) that must be used with 7447…

A: LED display can be broadly classified into two types  (i) Common Anode  In common Anode type display…

Q: In a PCM system, channels of 3 KHz bandwidth are used. If the uniform quantizer has 128 number of…

A: Channel capacity is defined is the maximum amount of data rate at which information can be reliably…

Q: A MicroBit is used to sample a noisy signal. Determine the possible voltage range of the signal if…

A: According to the question,  A MicroBit is used to sample a noisy signal. Determine the possible…

Q: What is PWM (Pulse Width Modulation), and how is it used in microcontroller applications? Provide…

A:

Q: For a single-tone modulating signal of 5 kHz and a carrier frequency of 600 kHz, list the…

A:

Q: Describe the principles of modulation and demodulation in the context of transmitting digital data…

A: Modulation and Demodulation are fundamental processes in the field of telecommunications, especially…

Q: Q4/:- For VCO-LO circuit block, if the message signal is the sine wave as shown in the figure below…

A:

Q: Describe TWO (2) advantages of DIGITAL over to ANALOG in data storage field.

A:

Q: How is Pulse Width Modulation (PWM) useful in microcontroller applications?

A: We need to explain uses of PWM in microcontroller applications.

Q: How do transistors amplify signals?

A: Transistor act as an amplifier if it's increases the strength of input signal. By using biasing we…

Q: What type of MOSFET is IRF640?

A: We need to tell about the type of given MOSFET.

Q: How should the initial data be erased from an EPROM?

A: Erasing the initial data from an EPROM (Erasable Programmable Read-Only Memory) requires a specific…

Q: What is the principle of the method for direct digital synthesis (DDS) of analog signals?

A: We need to explain the principle of the method for direct digital synthesis (DDS) of analog signals.

Q: What is the minimum possible energy per bit required for reliable communication over a white noise…

A: The minimum possible energy required for the reliable communication over the white noise analog…

Q: 12. An AM radio receives no station above 900 kHz. What is the likely problem? a) b) No input to the…

A: Solution of question (12): Given statement is "an AM radio receives no station above 900 kHz". Four…

Q: In a PCM system, 128 levels are present in the uniform quantizer. How many bits per sample are

A: Given information: In a PCM system, the number of levels present in the quantizer is 128.  The…

Q: Describe the difference of LCD and OLED displays with their working mechanisms and…

A: In the following section, the difference between LCD and OLED display has been given.

Q: In a PCM system, the maximum frequency of the analog input signal is 4 kHz. If the number of…

A: Given that  Maximum frequency of the analog input signal (fm) = 4 kHz Quantization level=2 =2n So…

Q: Determine Vas, ID and UDs-

A: