a. Complete the following timing diagram for the following circuit. The circuit works with falling edge. All of flip flops are JK-MS-FF. b. By use of timing diagram specify the count routine of the circuit. (Consider the main out-pout of each flip flop) fo J D J A J B J C K K K K clk clk A B D

a. Complete the following timing diagram for the following circuit. The circuit works with falling edge. All of flip flops are JK-MS-FF. b. By use of timing diagram specify the count routine of the circuit. (Consider the main out-pout of each flip flop) fo J D J A J B J C K K K K clk clk A B D

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Q: 1. Design a MOD 5 counter using a negative edge triggered JK flip flops and draw the resulting…

A: Mod-5 synchronous counter using JK flips with negative edge triggered:

Q: Design a 4 bit binary ripple counter that trigger as mention below on the edge of the clock. What…

A: Part (a): The circuit diagram for the given condition is shown below:

Q: For the circuit below X=1,B=1,Y=1,C=1. What will be the next state for the flip-flop? A. set B.…

A: Given: X=1, B=1, Y=1, C=1. The truth table for J-K flip flop is J K Q(n+1) 0 0 Q(n): Previous…

Q: 6) The inputs for a negative edge triggered JK flip flop are shown below. Draw the waveform for the…

Q: 2- Design synchronous counter using positive edge J-K flip flop to count the following states…

Q: Explain the difference between D-Latch and D flip flop with the help of diagram? If the ̅s and ̅R…

Q: 1-The waveforms in the figure below are triggered D flip flop and a gated D latch (i.e., with enable…

Q: What is the type of the flip flop? Why? Next state output Present state output Q At delay

A: The SR flip-flop, also known as a SR Latch, can be considered as one of the most basic sequential…

Q: Q5: For the data input and clock in Figure 01 (a), determine the states of each flip-flop in the…

A: Truth table of D Flip-flop is as shown below : Clk D Q Q¯ 0 0 1 1 0 1 0 1 Q Q 0 1 Q¯ Q¯…

Q: Obtain the timing diagram for the Master-Slave flip flop with appropriate assumptions for the…

Q: a) What type of counter does the circuit implements? b) Describe its output sequence? c)…

Q: Design synchronous counter(s) that go through each of the following sequence(s) f. 1 3 5 7 6 4 2 0…

A: The given sequence is: f. 1 3 5 7 6 4 2 0 and repeat

Q: Design a synchronous down counter which will count from binary 15 to 0. Use J-K Flip Flop to design…

A: Design a synchronous down counter which will count from binary 15 to 0. Use J-K Flip Flop to design…

Q: 2. An asynchronous down counter was build from four JK flip flop with clock of first flip flop is…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Design synchronous 3-bit up counter with the following sequence 0, 1, 3, 4, 5, 7, 0 by using J-K…

Q: (a) Provide a block diagram and a function table for the D-type flip-flop with falling edge…

A: Since you have posted multiple questions, we will solve the first question for you. If you require…

Q: Draw a ripple decade counter using negative edge-triggered JK flip- flops and draw the timing…

Q: Q: Consider the trailing edge triggered flip-flops shown: b. PRE Clock- Clock Clock CLR CLR a) Show…

A: Please find the detailed solution in below images

Q: Design a 4-bit synchronous counter that counts in 2,4,2,1 code. The counter shall count all Odd…

A: SEQUENTIAL LOGIC CIRCUITS: Sequential Logic circuits, unlike Combinational Logic circuits, have some…

Q: 1. Design a synchronous counter of three input (q1, q2, q3) using negative edge triggered T flip…

Q: a) Draw the graphic symbol (block diagram) of D Flip Flop on page. Mention/label all inputs and…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Counters designed by flip flops can be synchronous or asynchronous, which one of the following…

A: True Statment about Synchronous and asynchronous counter ?

Q: Design a Asynchronous Up counter that start it’s counting from zero and ends at 13 and again starts…

A: The counter should count up to 13, It is a MOD-13 Counter log2(13) = 3.7 Hence it required 4 flip…

Q: 1- Design synchronous counter using negative edge D- type flip flop to count the following states:…

Q: A counter which is counting in 4-2-1-0-1-2-4-2… order is given, answer the following questions:…

A: Given: A counter is counting in 4-2-1-0-1-2-4-2… order To find: a)state diagram b)state table c) JK…

Q: a) Build a falling edge triggered flip-flop circuit diagram

A: Faling edge triggered flip-flop circuit

Q: The first flip-flop of a ripple counter is clocked by none of the mentioned logic 1 O the Q' of the…

Q: Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops. The…

Q: Design asynchronous for the following sequence (0, 1, 2, 3, 4, 5, 6, 7, 8) counter and draw the…

Q: For asynchronous counter flip flops which of the following connection is correct? O a. All clocks…

Q: what is a standard synchronise circuit with 2 flip flops what do they do?

A: According to the question, we need to discuss the standard synchronize circuit with two flip-flops

Q: a. Complete the following timing diagram for the following circuit. The circuit works with falling…

A: a)

Q: Q4(a) Determine the Q output waveform of the flip flop in the Figure Q4(a). Assuming that the…

Q: Design a 2-bit randoin counter using T flip flop according to the following sequence: Start End 2 3

Q: b) How do we construct D flip flop using SR flipflop? Draw the circuit diagram with proper…

Q: Do Qo D Clock

Q: 3. Consider the counter shown in Figure 2, where the flip-flops are initially set to 0. (a)…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: / Design Synchronous counter using J-K flip flop to implement the following counting statements:…

Q: Question 1: a) Explain the concept of memory. If Flip-Flop can save only one bit and only the…

A: The digital circuits can be combinational as well as sequential circuits. The combinational circuits…

Q: of flip flop. design derivations including Karnaugh maps JK out of D

Q: How to use Flip Flops to design a six bits Parallel in /parallel out shift register ? Explain with…

A: FIND: Six bits parallel in / parallel out shift register by using flip flop.

Q: asynchronous counters differs from a synchronous counter in * (a) the number of state in…

A: The digital circuits can be either combinational circuits or sequential circuits. Combinational…

Q: Do Qo Clock

Q: Using JK flip flops, design a counter. The counter has one input x. When x=0 the counter counts…

A: Counter is a sequential circuit. A digital circuit which is used for a counting pulses is known…

Q: 1- Design synchronous counter using negative edge D- type flip flop to count the following states…

Q: Q5/ construct serial counter using PRE/CLR input flip flop that count in the following sequence…

Q: Q 1.4 « 4 » a. Complete the following timing diagram for the following circuit. The circuit works…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

L:03)

a. Complete the following timing diagram for the following circuit. The circuit works with
falling edge. All of flip flops are JK-MS-FF.
b. By use of timing diagram specify the count routine of the circuit.
(Consider the main out-pout of each flip flop)
fo
J A
J B
J D
K
K
K
K
clk
clk
A
В
C
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

9. Analysis of Synchronous Counters, in the following figure, write the logic equation for each input of each flip-flop. Determine the next state for state 010,011,100,111 as Q2Q1Q0 sequence. FF0 FFI FF2 Ko K, K2 CLK
Task 1: Custom Sequence Counter Using JK Flip Flop, Design a counter circuit that cycles through the sequence: 0, 5, 4, 6, 1, 7, and repeats. Follow these steps: a) State Diagram: Draw a state diagram representing the sequence. Each state should be expressed as a binary number. b) State Table: Create a state table for the counter, detailing current states, next states, and outputs. c) Flip-Flop Input Equations: From the state table, derive the input equations for the flip- flops. Treat any unused states as don't-care conditions. d) Simplification using K-maps: Use Karnaugh maps to simplify the flip-flop input equations. Optionally, verify your simplifications using Multisim. e) Circuit Diagram: Draw the circuit diagram. Task 2: 3-bit Up/Down Counter Using Flip Flop of your choice, design a 3-bit counter that counts up or down based on an input signal X. The counter should behave as follows: Initial State: On powerup, the counter starts at 0. Count Up (X=1): Sequence progresses through…
Design Master-Slave Flip Flop circuit diagram and write a short description.
Consider the T flip flop. (a) Using diagram, show how to construct the T flip flop using the JK flip flop. (ii) (b) Determine the Q waveform for a T flip flop with positive clock and the T inputs shown in Figure 5. Assume that Q = 0 initially. Clock
Q: Consider the trailing edge triggered flip-flops shown: a. b. C. PRE D Clock Clock Clock K q' CLR CLR a) Show the timing diagram for Q Clock b) Show a timing diagram for Q if there is no CLR input. i. ii. ii, the CLR input is as shown. Clock R CLR c) Show a timing diagram for Q if i. there is no PRE input. ii. ii. the PRE input is as shown (in addition to the CLR input) Clock CLR PRE
2- Using JK Flip flops, a 2-bit counter will be designed that will count down ((11-10-01-00) when the input is "0") and the random sequence given when the input is "1" (00-01-11-10). a) Construct the state table for the sequential circuit. b) Obtain the simplified input equations for flip-flops. c) Draw the logic circuit for the 2-bit counter.
3.) The design size of the synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and the son of your student number will not count decimals in two digits. A. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. B. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Design a Up Down Counter by using JK flip flop and verify the output of your designed circuit onany random input. Provide the following information as well:1. State table2. State diagram3. State equations4. Complete circuit diagram
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Analyze the following clocked synchronous sequential circuit by performing the following steps: please help me answer a,b,and c. (a) Write the equations for the flip-flops inputs and output equation. (b) Construct the transition and output tables. (c) Construct the transition graph.
Draw the logic circuit J-K flip flops by using following equation in figure.