A square piece is initially at 10 degrees Celsius everywhere. Each side is 0.05 m long. Then the four sides are instantly heated up to 25 degrees Celsius, 50 degrees Celsius, 30 degrees Celsius, and 0 degrees Celsius. a. Find how long it takes for the temperature profile of this square to become steady if the material is copper. What is the final temperature at the center of the square? b. Find how long it takes for the temperature profile of this square to become steady if the material is air. What is the final temperature at the center of the square? c. Which material takes longer to reach steady state and why?

A square piece is initially at 10 degrees Celsius everywhere. Each side is 0.05 m long. Then the four sides are instantly heated up to 25 degrees Celsius, 50 degrees Celsius, 30 degrees Celsius, and 0 degrees Celsius. a. Find how long it takes for the temperature profile of this square to become steady if the material is copper. What is the final temperature at the center of the square? b. Find how long it takes for the temperature profile of this square to become steady if the material is air. What is the final temperature at the center of the square? c. Which material takes longer to reach steady state and why?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.26P

See similar textbooks

Similar questions

What will be the rise in temperature in 30 minutes of a block of copper of 500-gram mass if it is joined to a cylindrical copper rod 20 cm long and 3.0 mm in diameter when a temperature difference of 80 degree Celsius is maintained between ends of the rod? The thermal conductivity of copper is 1.02 cal/cm2-sec-°C/cm (neglect heat losses). Please include FBD
(answer number 4-8 & main question) Two vessels of different shape and sizes are connected by means of a pipe with a valve. Vessel A has a diameter of 4 ft and the length is 1.8 m at the given pressure gauge of 1476.4 in Hg and temperature of 82°F. Another vessel spherical in shape contains the same gas at 15,000 torr gauge and 18°C. The valve is opened and when the properties have been determined, it is found out that the gauge pressure is 35.7 kgf/cm2 and the temperature is 21°C. If the barometric pressure is 755 mm Hg, find the following: Volume of Vessel A in in3 - done Pressure at Vessel A in psia - done Temperature at Vessel A in °R - done Pressure at Vessel B in psia Temperature at Vessel B in °R Pressure of the gas when mixed in psia Temperature of the gas when mixed in °R Atmospheric pressure in psi Main Question: What is the diameter of the spherical tank in inches if the gas is carbon dioxide?
Metal spheres, 10 mm in diameter, are to be annealed by heating them to 827°C then allowing them to cool slowly in air at 27°C to the point where they are in thermal equilibrium with the air. 2000 balls are annealed in one hour’s time. What is the total rate of their heat transfer if they are made of steel, lead, or copper? a.Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
QUESTION 22 Using the Wickström equation, determine the temperature you can expect reinforced steel to be if it is in a 300mm by 300mm concrete beam and is 30mm deep in to the concrete on the heated side. The beam is being heated by the ASTM E119 aurve on one side. Find the temperature of the reinforcing steel at 1.3 hours. O 565°C O 453°C O 718°C O -298.96°C
A steel bar has a temperature reading of 70°K inside storage A. it was then transferred to storage B wherein the air temperature if 10°K. After 3 minutes the temperature reading of the steel bar is 25°K. what would be the temperature of the steel after another 3minutes?
2. The drawing shows two thin rods, one made from aluminum Midpoint [a = 23 x 10-6 (C°)-'] and the other from steel [a = 12 × 10-“ (C°)-']. Each rod has the same length and the same initial temperature and is attached at one end to an immovable wall, as shown. The temperatures of the rods are increased, both by the same amount, until the gap be- tween the rods is closed. Where do the rods meet when the gap is closed? (a) The rods meet exactly at the midpoint. (b) The rods meet to the right of the midpoint. (c) The rods meet to the left of the midpoint. Aluminum Steel
To ensure a tight fit, the aluminum rivet used in airplane construction are made slightly larger than the rivet holes and cooled by dry ice (solid CO2) before being driven. If the diameter of a hole is 0.500 cm, what should be the diameter of a rive at 20 degree Celsius if its diameter is equal that of a hole when the rivet is cooled to -78 degree Celsius, the temperature of dry ice? Assume the coefficient of expansion to remain constant. (Given and solutions)
The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal conductivity is 60 W/m-C. The voltage and current flowing into the heater are 220V and 5A, respectively. Find the temperature at the top portion of the pan. Sketch diagram and show pertinent solutions. Box your final answer and express numerical values in 2 decimal places
1.The height of the Washington Monument is measured to be 170 m on a day when the temperature is 35.0 °C. What will its height be on a day when the temperature falls to -10.0 ° C? Although the monument is made of limestone, assume that its thermal coefficient of expansion is the same as marble's. 2.How much taller does the Eiffel Tower become at the end of a day when the temperature has increased by 15 ° C? Its original height is 321 m and you can assume it is made of steel. 3.What is the change in length of a 3.00-cm-long column of mercury if its temperature changes from 37.0 ° C to 40.0 ° C, assuming the mercury is unconstrained? 4.How large an expansion gap should be left between steel railroad rails if they may reach a maximum temperature 35.0 ° C greater than when they were laid? Their original length is 10.0 m
The heat conducts through the shape below. The temperature of the right face is 93 °C, while the left face is at 23 °C. If the top and bottom faces are completely insulated, and the thermal conductivity of the material decreases with decreasing temperature. * Assume that the thermal conductivity is 100 at 23, decreased to 10 at 93. A) Sketch the temperature profile inside the plate. B) If both sides of the plate in the above problem is exposed to air: Left side (h = 20 W/m2K, TL = 20 °C) and right side (h = 90 W/m2K). Calculate the temperature of the air on the right side.
The 40mm diameter steel rod AB shown in Figure 2 is resting on frictionless rollers between two steel plates. End A is just touching the left hand steel plate. 2. Steel plate Steel plate A В 1500mm 1mm Figure 2 There is a gap of 1mm between the end B and the right hand side steel plate. The temperature of the rod increases by an amount AT and this increase in temperature causes the two ends of the rod to press against the steel plates. This action causes the right hand steel plate to move to the right by 0.5mm while the left hand plate does not move. The Young's modulus value for steel is 210,000N/mm?. Taking any assumptions that you deem necessary calculate the increase in temperature AT required to cause the rod to buckle.
How are you solving the equations in step 4 to get the values for Tad, ab, ac? Especially when each equation has two unknowns.