Q1: An engine shaft running at 120 r.p.m. is required to drive a machine shaft by means of a belt. The pulley on the engine shaft is of 2 m diameter and that of the machine shaft is 1 m diameter. If the belt thickness is 5 mm; determine the speed of the machine shaft, when. 1. there is no slip; and 2. there is a slip of 3%.

Q1: An engine shaft running at 120 r.p.m. is required to drive a machine shaft by means of a belt. The pulley on the engine shaft is of 2 m diameter and that of the machine shaft is 1 m diameter. If the belt thickness is 5 mm; determine the speed of the machine shaft, when. 1. there is no slip; and 2. there is a slip of 3%.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
IS. 03 16. The shaft, as shown in Fig. 14.20, is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 3.5. B. TA2 A D. TA 150 -100- TB2 100 All dimensions in mm. Fig. 14.20 The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensile stress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion and bending factors as 1.25 and 1.75 respectively, find the shaft diameter. Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare the weights of the two shafts. Ans. 30 mm : 24 mm: 1.82]
A line shaft with a power of 100 kW at a speed of 1,200 rpm had a rectangular key used in it for pulley connection. Consider the shearing stress of the shaft to be 40 N/mm2 and the key to be 200 N/mm2 . Find the shaft diameter in mm. A. 46.62 C. 42.66 B. 50.62 D. 38.66
(i) An engine shaft running at 4.5r.p.s. is required to drive a machine shaft by means of a belt. The pulley on the engine shaft is of 2m diameter and that of the machine shaft is 1m diameter. If the belt thickness is 7mm.Determine the speed of the machine shaft, when 1. There is no slip 2. There is a slip of 3%
Q: The sunwheel D has 20 teeth, the gear B is 50 teeth, internal gear C is fixed. The input shaft rotates at 2100 r.p.m. Determine the speed of the output shaft and the torque required to fix C when the gears are transmitting 30 kW. Output shaft Input shaft D
1. A compound train consists of six gears. The number of teeth on the gears are as follows : D E F 50 Gear B C A No. of teeth: 60 40 25 24 30 The gears B and C are on one shaft while the gears D and E are on another shaft. The gear A drives gear B. gear C drives gear Dand gear E drives gear F. If the gear A transmits 1.5 kW at 100r.p.m. and the gear train has an efficiency of 80 per cent, find the torque on gear F. [Ans. 30.55 N-m) 2. Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 120 r.p.m. and the other at 360 r.p.m., find the number of teeth on each wheel, if the module is 8 mm. Also determine the exact distance apart of the shafts. (Ans. 114, 38 ; 608 mm] In a reverted gear train, as shown in Fig. 13.32, two shafts A and B are 2 in the same straight line and are geared together through an interme- 3. diate parallel shaft C. The gears connecting the shafts A and C have a module of 2 mm and those…
1. An engine running at 150 rpm drives a line shaft by means of a belt. The engine pulley is 750 mm diameter and the pulley on the line shaft is 450 mm. A 900 mm diameter pulley on the line shaft drives a 150 mm diameter pulley keyed to a dynamo shaft. Find the speed of dynamo shaft, when: 1. There is no slip, 2. There is a slip of 2% at each drive. 150 L 900 ( 3 ) ( 4 ) 750 Dynamo Shaft (1 ) ( 2 ) Line Shaft Engine Shaft 450 2. A leather belt 9 mm x 250 mm is used to drive a cast iron pulley 900 mm in diameter at 336 rpm. If the active arc on the smaller pulley is 120° and the stress in tight side is 2 MPa, find the power capacity of the belt. The density of leather may be taken as 980 kg/m*, and the coefficient of friction of leather on cast iron is 0.35.? 3. A flat belt is required to transmit 30 kW from a pulley of 1.5 m effective diameter running at 300 rpm. The angle of contact is spread over 11/24 of the circumference. The coefficient of friction between the belt and pulley…
Q.6 The Ray Precision Engineering company uses CNC Lathe machine. The reliability of Gear Box of CNC Lathe machine is given by: e-(Vo.002)•t t20 Evaluate the following: (i) The Reliability for the first 40 hours of operation; (ii) The MTTF and the failure rate; (iii) The Design life for a reliability of 85%.
An engine, running at 150 r.p.m., drives a line shaft by means of a belt. The engine pulley is 750 mm diameter and the pulley on the line shaft being 450 mm. A 900 mm diameter pulley on the line shaft drives a 150 mm diameter pulley keyed to a dynamo shaft. Find the speed of the dynamo shaft, when 1. there is no slip, and 2. there is a slip of 2% at each drive.
3. A shaft 120 mmm ...
5. A transmission shaft has a torsional stress of 7,000 psi. If the diameter of shaft is 1.5 inches, what torque can be safely transmitted in lb-in? A. 4,638.77 B. 4,494.88 C. 4,266.66 D. 4,051.55
4)The tooth shape factor Y, for helical gears should be determined by A.Tooth number z B. 2 С. cos B D. 2 3 cos' B