5.59 Determine the magnitude of the horizontal component of the anchoring force required to hold in place the sluice gate shown in Fig. 5.59. Compare this result with the size of the horizontal compo- nent of the anchoring force required to hold in place the sluice gate when it is closed and the depth of water upstream is 10 ft. 10 ft 1.5 ft 4 ft/s Figure P5.59

5.59 Determine the magnitude of the horizontal component of the anchoring force required to hold in place the sluice gate shown in Fig. 5.59. Compare this result with the size of the horizontal compo- nent of the anchoring force required to hold in place the sluice gate when it is closed and the depth of water upstream is 10 ft. 10 ft 1.5 ft 4 ft/s Figure P5.59

Name: 5.59 Determine the magnitude of the horizontal component of theanchor
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 5.59 Determine the magnitude of the horizontal component of theanchoring force required to hold in place the sluice gate shown inFig. 5.59. Compare this result with the size of the horizontal compo-nent of the anchoring force required to hold in pla

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ROLLER GATE WATER SURFACE R=4 m WATER SURFACE C. 307 6.0 m 30- HÍNGE DAM Fig. 3.60 Fig. 3.59 21. Find the horizontal and vertical components of the water pressure exerted on a tainter gate of radius 4 m shown in Fig. 3.60. Consider width of the gate unity. (Problem 3.25)
thi 40 A vertical sluice gate (4m) wide and (3m) deep contains water on both of its sides. On the upstream side, the water is (6m) deep and on the downstream side it is (2.5m) deep from the bottom of the sluice. What is the resultant pressure force on the gate and the position of this resultant force from the hinge
A vertical sluice gate spans the full width of a rectangular channel 6.0 m wide. If the downstream depth is 1.2 m and the upstream depth is 6.0 m, find the horizontal force on the gate.
Problem 2 Hinge A stop-block on the edge of the gate at B will break whenever the force reaches 40kN. The gate is rectangular in shape, which is Im by 1.5m in area. Find the critical water depth, h. [5.77m) h 1m Stop-block
The A have 4.8 m wide sluice gate "ab" shown, tangent to vertical wall at "a", holds back Water. The surface of the gate in contact with the water can be taken as part of a cylinder with radius of B at 4.5m. The angle (theta) is C at 31°. Determine the following: a. Horizontal force acting on curve b. Location of horizontal force from the water surface. c. Total Force on the curve I W.S. Im
3. Determine the magnitude and direction of the resultant force due to water on a quadrant shaped cylindrical gate as shown in Fig. Ex. 3.9. Check whether the resultant passes through the centre. 4 m Hinge WL Gate CG: 4r 4 m 4 m 123276 78480 Figure Ex. 3.9
3. Reciprocal of the density 6. The intensity of the molecular attraction per unit length along any line in the surface 7. weight per unit volume 9. It is either positive or negative, depending upon whether its level is above or below the atmospheric pressure reference produced by the attraction of the water molecules to a solid surface 4. The pressure in the ideal gas law must be expressed as 5. It is used to indicate the normal force per unit area at a given point acting on a given plane within the fluid mass of interest 8. The ratio of the density of the fluid to the density of water at some specified temperature 10. mass per unit volume TASK 2: SOLVE PROBLEMS INVOLVING THE PROPERTIES OF FLUIDS. Multiple Choice. Instructions: Select the correct answer for each of the following questions. Put a check mark on letter/s corresponding to the correct answer/s. STRICTLY NO ERASURES ALLOWED. 1. The correct units on viscosity are: (A) kg/(s · m) (B) kg · m/s (C) kg · s/m (D) kg · m/s2 5. Two…
3.47 A rectangular container of water undergoes constant accelera- tion down an incline as shown. Determine the slope of the free sur- face using the coordinate system shown. y `a, = 3 m/s? 0 = 30° P3.47
5. Gate ABC is shaped in the form of a circular arc and pivots about point O. The arc extends a width b in the plane of the figure. 6 m Water A R = 6m 6 m Questions: (a) Determine the horizontal component of the resultant hydrostatic force (per unit width) acting on the gate. (b) Determine the vertical component of the resultant hydrostatic force (per unit width) acting on the gate. (c) Determine the magnitude and direction of the resultant hydrostatic force. (d) Does the line of action of this force pass through point O? Justify your answer.
... Air; P = 36 KPa Oil; SG = 0.82 1.7m Water 1.8m Unknown liquid 4.2m SG = 1.32 2m 60° Determine the magnitude of the total hydrostatic force acting on the 2m x 4m gate shown. (A) 762.97 KN B 733.16 KN (©) 794.33 KN D 687.34 KN (E) No answer among the choices 4m
An open cylinder tank, D= 1.0m, h=1.5m, contain water at depth 1.0m. If this tank rotate about its central vertical axis. Its the angular velocity without falling water from its open end * 8 rad/sec 8 rev/min 5 rad/sec 4.5 rad/min none of these=..
Quest-4 The top surface of a vertical rectangular gate, with 16 m width and 12 m height, and the upper surface of height coincides with the free water surface. Find the depth of the centre of pressure.