WITH DESCRIPTION AND STEPS APPLIED, TO HELP ME UNDERSTAND APPROPRIATELY A hydraulic press cylinder has an internal diameter of 30 cm andis designed to work at a 10 MPa pressure. Considering that thecylinder's construction material must not be stressed beyond 20MPa, determine the thickness and stresses at the inner and outerradius of the cylinder. Plot the variation of the radial and hoopstresses across the thickness of the cylinder's wall.

final answer = P= 10MPat >= 7.5cmσh = 20MPaσr = 10MPaPlot the variation of radial and hoop…

Answered: A hydraulic press cylinder has an…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A compound cylinder is made by shrinking a jacket with an outer diameter of 200 mm on a hollow cylinder with diameter of 100 mm and 150 mm. When the compound cylinder is subjected to an internal pressure of 35MNm-2, the maximum circumferential stress in both cylinders is the same. Calculate the maximum stress developed at the internal diameter of the jacket.
For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the internal pressure is 5 MPa. Determine the minimum and maximum stresses induced in the cylinder.
A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is 35 cm and the steam pressure is 8.5 kg/cm2. Assuming that the bolts are not initially stressed, find the diameter of each of the bolts if the tensile stress is not to exceed 200 kg/cm2.
A steel cylindrical pressure vessel with closed ends is 25 cm external diameter and 5 mm thick It is wound closely with a single layer of circular wire of diameter 1.2 mm. Under the tension of 96 N/mm'. If the cylinder is treated as thin. Calculate (1) Initial stress in cylinder. (ii) Initizl pressure which will produce a stress of 48 N/mm2.
A aluminum tank with a wall thickness of 2mm and radius of 120mm is 9m long was pressurized to 290kPa. Determine the circumferential stress in MPa.
A steel tube of 200 mm external diameter is to be shrunkonto another steel tube of 60 mm internal diameter.The diameter at the junction after shrinking is 120 mmbefore shrinking on, the difference of diameters at the junctionis 0.08 mm. Calculate the radial pressure at the junctionand the Hoop stresses developed in the two tubes aftershrinking on.Take E = 2 x 10³ N/mm²
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
The wall thickness of a 1.2 m diameter spherical tank is 1.6875 mm. Calculate the allowable internal pressure if the stress is limited to 55 MPa. If i will get the same answer again I will report and downvote.
State clearly the assumptions made in Lame's theory of thick cylinders. Assuming fundamental formula for radial and hoop stresses in a thick cylinder, prove that when a collar having an internal diameter D, and an external diameter D, is shrunk on to a solid shaft of the same material and having an external diameter D1 + 8(8 being small shrinkage allowance). then the radial pressure at the E8 (D; – D²) 2 D,D joint is equal to
A closed thin walled cylindrical vessel has a diameter D of 290 mm, a wall thickness t of 5 mm and length L of 210 mm. It is subject to an internal pressure P of 18 MPa causing circumferential stress and longitudinal stress in the vessel. Calculate the longitudinal stress due to the internal pressure. Give your answer in MPa to 3 significant figures. 00 P D 60 de OL
Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin.
A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The cylinder is designed to store fluid at 80 MPa:(a) Determine the external pressure necessary to bring the hoop stress at the outer wall of the cylinder to zero. (b) Draw the variations of the hoop and radial stress across the thickness of the wall. Indicate the stress values at both inner and outer radii.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS