Using the Wickström equation, determine the temperature you can expect reinforced steel to be if it is in a 300mm by 300mm concrete beam and is 30mm deep in to the concrete on the heated side. The beam is being heated by the ASTM E119 aurve on one side. Find the temperature of the reinforcing steel at 1.3 hours. O 565°C O 453°C O 718°C O -298.96°C

Using the Wickström equation, determine the temperature you can expect reinforced steel to be if it is in a 300mm by 300mm concrete beam and is 30mm deep in to the concrete on the heated side. The beam is being heated by the ASTM E119 aurve on one side. Find the temperature of the reinforcing steel at 1.3 hours. O 565°C O 453°C O 718°C O -298.96°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pick the best soultion for the multiple choices. Modulus of resilience is: Slope of elastic portion of stress – strain curve Area under the elastic portion of the stress –strain curve Energy absorbed during fracture in a tension test Energy absorbed during fracture in an impact test Slope of the plastic portion of the stress- strain curve ( ) Fatigue failure occurs under the condition of: High elastic stress High corrosivity High stress fluctuations High temperature High rate of loading ( ) Creep failure of a material occurs most rapidly when the operating temperature is: Cryogenic temperature Equal to its melting point Grater than 0.4 times its melting point in K Greater than 200 oF Close to boiling point ( ) Young’s modulus of a material is indicative of its: Tensile strength Yield Strength Ductility Stiffness Corrosion Resistance…
Which R134a table is referring to? My reference as attached. The answer result should be different?
Choose the correct answer 1- In annealing, cooling is done in which of the following media: a- Air b- Water c- Oil d- Furnace 2- In normalizing cooling is done in which the following medium: a-NaOH b-Polymer c-Brine d-Air 3-Miled steel ean be converted into high earbon steel by which of the following heat treatment process: a- Normalizing b- Annealing c- Nitriding d- Case hardening 4-Which one of the following is the solid carburizing material: a-Charcoal b-NH4 c-NAOH d-CH4
A ductile cast-iron bar is to support a load of40,000 lb in a heat-treating furnace used tomake malleable cast iron. The bar is located in aspot that is continuously exposed to 500C. Designthe bar so that it can operate for at least 10years without failing.
Question 1 A composite component is comprised of a tube and a concentric rod running inside it, both with a length of 1.5 meters. The tube is made of copper and has inner and outer diameters of 60 mm and 100 mm, respectively, a coefficient of thermal expansion and elastic modulus of 17 ×10-6C and 117 GPa, respectively. The rod is made of aluminium with a diameter, coefficient of thermal expansion and elastic modulus of 50 mm, 23 ×10-°C and 80 GPa, respectively. If the composite is exposed to a temperature rise of 120°C, determine: 1.1 The sense and magnitude of the stresses induced in the composite if it is not restrained. 1.2 The sense and magnitude of the stresses induced in the composite if it is partially restrained with an allowed free expansion of 0.3 mm.
A circular cross-sectional rod made of AISI Type 303 Stainless Steel is normally operated at126oF. Length and radius of the rod are 1.5 ft and 1.75 in., respectively. What would be thechange in length of the rod, if it is subjected to a temperature of 214oF? Coefficient of thermal expansion of the rods’ material is 9.6 × 10^-6 in./in. Degrees Fahrenheit.
3. The starting length of a shaft is 25.00 mm. This shaft is to be inserted into a hole in an expansion fit assembly operation. To be readily inserted, the shaft must be reduced in length by cooling. Determine the temperature to which the shaft must be reduced from room temperature (20° C) in order to reduce its length to 24.98 mm. Refer to the Table below. Volumetric properties in U.S. customary units for selected engineering materials. Coefficient of Thermal Density, p Expansion, a Melting Point, T Material g/cm Ib/in c'x 10 x 10 °C 'F Metals Aluminum 2.70 0.098 24 13.3 660 1220 Copper Iron 0.324 0.284 0.410 8.97 17 9.4 1083 1981 2802 7.87 12.1 6.7 1539 Lead 11.35 29 16.1 327 621 Magnesium Nickel 1.74 0.063 0.322 0.284 26 14.4 7.4 650 1202 8.92 13.3 1455 2651 7.87 7.31 19.30 7.15 Steel Tin 12 23 6.7 0.264 12.7 232 449 Tungsten Zinc 0.697 4.0 2.2 3410 6170 0.258 40 22.2 420 787 Ceramics b. Glass 2.5 0,090 1.8-9.0 1.0-5.0 Alumina 3.8 0.137 9.0 5.0 NA NA b. Silica 2.66 0,096 NA NA…
Excellent combinations of hardness, strength, and toughness are obtained from bainite. One heat treater austenitized a eutectoid steel at 750°C, quenched and held the steel at 250°C for 15 min, and finally permitted the steel to cool to room temperature. Did he produce the required bainitic structure? Use the diagram below in your answer 900 600 700 14 00 Y. 400 12 52 M. 00 57 M. 100 0.3 10 10 10 Answer: Time Temperature ("C) Rockwell Chardnens
Carbon idallowed to diffuse through a steel plate 23.1 mm thick. The concentrations of carbon at the two faces are0.71 gnand 01g whhare mataontant It the pre exponential and activation energy are 0.0000006 ms and 75453 Mmol respectively compute the temperature at which the diffution fa in 52 10 P Give your answer in degrees.Celsius to 1 decimal place
Brittle Dune Buggy Parts A mechanic who was building a lightweight dune buggy needed some high-strength aluminum parts. Since he had access to a heat-treating furnace, he decided to do the solution heat-treating and aging process himself. He obtained 2024 aluminum bars and made the parts. Then her heat treated the part in a furnace to 1200 deg F., quenched them, and allowed them to age naturally. He noticed they had small blisters over their surfaces and when he began to hammer one in place, it broke in two places. What did he do wrong? Could the parts be salvaged in any way?
Subject: strength of materials A spherical vessel is to contain air at an average temperature of 25°C. The average mass is 250 kg. If the inside diameter is 2.5 meters, Find the required thickness of the vessel in INCHES made of steel with yield strength of 52.5 ksi. The joint efficiency is set to 75.25% and factor of safety of 5.25. Note : remember this question belongs to strength of materials Help me urgent thank you
Q1. A bimetallic strip is used in temperature control systems as a safety component for automatic shutdown. You get two metal (Invar and yellow brass) with a length of 3.5 cm and thickness of 0.25 mm to construct the bimetallic strip. The system should work at the temperatures between -20 and 130 °C. Calculate the radius of curvature at the extremes of the design temperature range if two metals are bonded at 30•C.