Answered: A sinusoidal voltage is given by v =…

A sinusoidal voltage is given by v = 150 sin(314t + 30°)V. Find: (a) the maximum value of voltage (b) frequency (c) the voltage emf when t = 5ms (d) time when the voltage first reaches -75 V.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Q Find the capacitance C necessary to improve the power factor to 0.95 lagging in the circuit shown…

A: Z = 20∠30°Z = 20(Cos 30°+j Sin 30°)Z = 20 32+j2Z = 103+j 10ΩBoth branches are parallel,Total…

Q: The circuit below is operating in the sinusoidal steady state with V(t)=35cos(1000t) V. (a)…

Q: An AC circuits with 50 Hz voltage of 240V effective value is impressed on an inductance of…

Q: Q5 The network shown is operating in the steady state with sinusoidal voltage sources. If v = 2 cos…

A: We need to determine the voltage Va(t).

Q: Given the circuit shown below while assuming a sinusoidal steady state, 500 250 0 2 A 10 V1 •j 50 0…

Q: ELECTRICAL CIRCUIT: Solve the problem and show your complete solution. The maximum values of the…

Q: he AC circuit below has o = 10 rad/s and is in steady state. The phasor iagram shows the phasors of…

Q: A sinusoid v, =V cos (at + 35°) leads another sinusoid v,=V2 sin (at + $) by 120 degrees. What is in…

Q: Given V, = 20 sin(@t + 60°) and V, 60 cos(wt – 10°). What is the phase angle %3D %3D between the…

A: Given Data: V1 = 20 sin (wt + 60) V2 = 60 cos( wt-10)

Q: A sinusoidal voltage trace displayed by an oscilloscope is shown, if the 'time/div' switch is of 500…

A: In this question we will find frequency , peak to peak voltage , amplitude , RMS value and…

Q: Problem: Find the equation of the current ( find the sinusoidal expression for the current ) for the…

A: We need to find out the current through resistor

Q: 2. What is the value of a sinusoidal voltage at 5 us (micro second) from the positive going zero…

A: 2) To find the value of a sinusoidal voltage at 5 microseconds Given: Vp = 20 v and f = 50 kHz

Q: The circuit in the figure is in sinusoidal steady state. Find steady state current iR(t) by using…

A: Solution: Given, A circuit diagram with values as shown below…

Q: 2.) A sinusoidal voltage trace displayed by an oscilloscope is shown, if the 'time/div' Hs, switch…

Q: An industrial coil is modeled as a series combination of an inductance L and resistance R, as shown…

A: This question belongs to circuit theory . It is based on the concept of vector addition of voltage…

Q: v0- 100 sin(10) at tKO v(0F 200 sin(100) att>0 A coil has been connected to an AC source for a long…

Q: Problem 1.3 (Sinusoids and Exponentials) All signals are defined for – ∞ < t < ∞. (a) Sketch the…

A: We know ther Fundamental time period,T =1/f Where f= fundamental frequency in hertz . And in…

Q: QUESTION 2 io + 10 cos 21 V C 6 sin 2t V For the circuit shown above, what is the amplitude of the…

Q: A sinusoidal current reaches its first negative maximum, - 50 mA, at t = (7 n /8)ms and has a period…

Q: Given the sinusoidal voltage ? (?) = 70 sin(4π? + 10) V find: (i) The amplitude of the maximum…

A: The expression of sinusoidal voltage is, The expression of standard sinusoidal voltage is, a).…

Q: A sinusoidal voltage has a peak value of 15 V, has a frequency of 125 Hz, and crosses zero with…

Q: A sinusoidal voltage v(t) has an rms value of 20 V, has a period of 100 μs, and reaches a positive…

Q: A sinusoidal voltage trace displayed by an oscilloscope is shown, if the 'time/div' Hs, switch is on…

Q: Transform the following sinusoids to phasors: (a) – 20 cos(41 + 135°) (b) 8 sin(201 + 30°) (c) 20…

Q: An industrial coil is modeled as a series combination ... of an inductance L and resistance R, as…

Q: Assignment (8)-Sinusoidal a + 302 125sin(25001 + 60°) mA( 1) 2523 S10mH b Find the phasor domain…

A: In this question, Draw the phasor circuit, calculate the voltage Vab in phasor and time domain.…

Q: set of ac phasors, find the indicated resultant.

A: Given- For series RC circuit- VR= 8∠0° Volts VC= 5∠-90° Volts To find- Resultant, VT=?

Q: Find the current of the resistor in the sinusoidal steady state (use phasors). (100 points) L = 2H,…

Q: Multiples of 360° may be added to or subtracted from the argument of any sinusoidal function without…

A: According to question we discuss about A1.

Q: 4. Consider the two sinusoidal signals X1(t) = 3cos(@t + t/2) and X 2(t) = (3+j2)cos(@t). Let P(t)…

Q: 1. The current source in the circuit shown below is generating a sinusoidal waveform such that i,1)…

Q: Volts 20 10 5 10 15 20 25 30 35 40 45 50 t (ms) -10 - -20 Given the above graph. Which general…

Q: The electric field in the phasor form is given by E, = 50 e-jmâx + 50 e-j"ây %3D Express the field…

Q: 1.The voltage across a 10 Q resistor is: v(t) = 50 sin 100t. a. Find the sinusoidal expression for…

Q: In the circuit shown below, the AC voltage is V0 cos(ωt). Find: (a) The current I(t) through the…

A: Detailed solution is attached in the form of notes. Please go through it. Thank you.

Q: A pure inductor of 20.0 mH is connected to a source of 220 V. Find the RMS value of current in the…

A: Given, Source voltage, Vsrms=220 V Inductance, L = 20 mH Frequency of source, f = 50 Hz

Q: find the phase, frequency, amplitude, period of the sinusoid v(t) = 10sin(377t +45°). Graphically…

A: v(t) = 10sin(377t +45°)

Q: At t=−2 ms, a sinusoidal voltage is known to be zero and goingpositive. The voltage is next zero at…

A: (1) Write the expression for half time-period. T2=8 ms--2 msT2=10 msT=20 ms

Q: -T = r(cos0 + sin@cosø)

Q: The circuit given below is operating in the sinusoidal steady state. Find the value of w if i, =…

A: Given: A circuit operating in sinusoidal steady state. According to question: ∵io=40sinωt+21.870mAIn…

Q: 4. Consider the two sinusoidal signals x1(t) = 3cos(@t + n/2) and x 2(1) = (3+j2)cos(@t). Let P(1)…

Q: Example .1: Given the sinusoid 30 sin(4 mt-75°), calculate its amplitude, phase angular frequency,…

Q: Find the Thevenin equilvent circuit

A: The circuit diagram is:

Q: 4. A 50 Hz, alternating voltage of 150 V (rms) is applied independently to (a) Resistance of 10 n,…

Q: For the following sinusoids, TU x(t): = 230 cos (377t + F y(t) = 110 sin(377t +80°) a) Convert the…

Q: A circuit has an ac voltage source and a resistor and capacitorconnected in series. There is no…

A: Ohm's law: This law states that the current is directly proportional to the voltage and inversely…

Q: The expressions for the steady-state voltage and current at the terminals of the circuit seen in…

Q: Two alternating voltages are given by vị = 120 sin wt volts and v2 = 200 sin(wt volts. Obtain the…

A: This question belongs to basic electrical . It is based on the concept of calculation of expression…

Question

A sinusoidal voltage is given by v = 150 sin(314t + 30°)V.
Find: (a) the maximum value of voltage (b) frequency (c) the
voltage emf when t = 5ms (d) time when the voltage first
reaches -75 V.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
An alternating current is given by the expression i = 200 sin (314t + T/6) amperes. The maximum value is and the frequency of the current is
18 In the circuit shown in the figure below, for what value of C will the current-I be in phase with the sinusoidal source voltage V= sin2t? Vs (1 + j1) Q (a) -F 4 (b) (c) (d) 1F /-
Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of using a single 14 V dc voltage source.
An AC voltage source and a resistor are connected in series to make up a simple AC circuit. If the source voltage is given by AV = AVmax sin(27ft) and the source frequency is 19.0 Hz, at what time t will the current flowing in this circuit be 61.0% of the peak current? 5.922 X Note that the voltage in this AC circuit is a sine function. Did you use the correct units for the argument of the sine function? ms
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
PHASE RELATIONSHIP SINUSOIDAL( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
A sinusoidal alternating voltage has an r.m.s. value of200 V and a frequency of 50 Hz. It crosses the zero axis in apositive direction when t = 0. Determine (i) the time when volt-age first reaches the instantaneous value of 200 V and (ii) thetime when voltage after passing through its maximum positivevalue reaches the value of 141.4 V.
The source in the circuit shown is a sinusoidal source. The supply voltages across various elements are marked in the figure. The input voltage is: 3V- ww -14 V-10V moon It
If an electrical circuit draws 100W + J100VAR from a sinusoidal source, then what would the circuit be? Explain why. a) a pure resistor circuit b) a series or parallel R-L circuit c) a series or parallel R-C circuit d) a series L-C circuit