An AC voltage source and a resistor are connected in series to make up a simple AC circuit. If the source voltage is given by AV = AVmax sin(27ft) and the source frequency is 19.0 Hz, at what time t will the current flowing in this circuit be 61.0% of the peak current? 5.922 X Note that the voltage in this AC circuit is a sine function. Did you use the correct units for the argument of the sine function? ms

An AC voltage source and a resistor are connected in series to make up a simple AC circuit. If the source voltage is given by AV = AVmax sin(27ft) and the source frequency is 19.0 Hz, at what time t will the current flowing in this circuit be 61.0% of the peak current? 5.922 X Note that the voltage in this AC circuit is a sine function. Did you use the correct units for the argument of the sine function? ms

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

An ac voltage represents by a sinusoidal waveform as shown in Figure 6 below. a) Define: i. The period ii. The frequency b) Referring to Figure 6, given that the peak voltage Vp = 24 V. Determine: i. The period, T ii. The frequency, f. ii. The angular velocity, w. iv. The voltage, VRMS V. Write the mathematical expression for the sine wave in Figure 6 to represent the ac voltage.
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
The ripple factor for pure dc is Answer:
Q18. An AC waveform is shown in figure B3. 4 10 20 30 40 50 70 100 Time (ms) 110 -2 -3 -4 -5 Figure B3 i) For the above waveform, determine a. Peak-to-peak voltage b. Time period c. Frequency ii) For the above waveform, determine a. Peak Factor b. Form Factor
The waveforms show a voltage (v) and a current (i) for an AC circuit. The current signal has a value of 0A at t = 25ms, 75ms, and 125ms. The voltage signal reaches a maximum value of 5 volts at t = 83.33ms and 183.33ms. 6 5 4 3 i 1 1. 0.05 0.1 1 0.15 0.2 0.25 0.3 -1 1. -2 -3 -4 -5 -6 a) What is the frequency of the current signal, in Hz? b) What is the angular frequency of the voltage signal, in rad/s? c)What is the phase difference between the current and voltage [5 pts] signals (in degrees)? d)Does the voltage signal LEAD or LAG the current signal?
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
3-9 An rms ac voltmeter and a peak-to-peak-reading ac voltmeter are to be used to determine whether three ac signals are sinusoidal. Deter. mine whether the signals are sinusoidal if the following readings are obtained First signal Second signal Third signal peak-to-peak reading = 35.26 V rms reading. - 12.00 V peak-to-peak reading - 11.31 V rms reading = 4.00 V peak-to-peak reading = 25.00 V rms reading -8.83 V
An inductor of 150hms and resistance of 10 Ohms are connected in series to a 230V, 50 Hz ac supply. Determine the active and reactive power and power factor in the circuit.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Answer (c). What are Ac voltage at each point indicated (A,B,C,D,E) in the circuit with Vs = 100mVp-p
Facts A clipper is a device that removes either the positive half (top half) or negative half (bottom half), or both positive and negative halves of the input AC signal. In other words, a clipper is a device that limits the positive amplitude or negative amplitude or both positive and negative amplitudes of the input AC signal. In some cases, a clipper removes a small portion of the positive half cycle or negative half cycle or both positive and negative half cycles. In the below circuit diagram, the positive half cycles are removed by using the series positive clipper. Question: In your own opinion. Why do we need to clip a certain amount of voltage in positive or negative or on both sides? What is the benefit of that in our devices or circuits in doing such thing?