Answered: Two alternating voltages are given by…

Two alternating voltages are given by vị = 120 sin wt volts and v2 = 200 sin(wt volts. Obtain the sinusoidal expression for v1 - v2 by resolution of phasors.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.3MCQ: If a phasor representation of a current is given by I=70.745A, it is equivalent to a. 100e/45 b....

See similar textbooks

Related questions

Q: An inductive circuit of resistance of 2 ohms and inductance 0.01 H is connected to a 250 V, 50 Hz su...

Q: A current transformer has 15 turn on the primary and 75 turn on the secondary. The relay burden is (...

A: We are authorized to answer one question at a time, since you have not mentioned which question you ...

Q: VcC 10V R1 10kn 10% RC {3.6kN 10% C2 B = 150. 01 2N3904 RS C1 1kn 10% RL vs 1.5kn 10% CE 470uF R2 RE...

A: We need to find out DC current , input, output impedance , output voltage for given input and voltag...

Q: Two positive charges Ql and Q2 are separated by a distance r. The charges repel each other with a fo...

Q: (65) What is the output of the system with 1 h[n] = G u(n) in response to the input %3D 2 x[n] = 3+ ...

A: As a system is considered, which have some input then it gives an output, that output is due to the ...

Q: Q4): A) Find the Equation of the line that passing in point (3,5) and parallel or perpendicular to t...

A: As per our guidelines we are supposed to be answer only the first question. Kindly repost the other ...

Q: Q5 / Find the current in the 20 resistance of the network shown in fig.(5) 2V 3 12V 6V- 8V

A: Given circuit,

Q: A cube of a material of side 1 cm has a resistance of 0.001 Q between its opposite faces. If the sam...

A: Since you have asked multiple question, we will solve the first question for you. If youwant any spe...

Q: D1 R1 5kQ 1n4001 D2 V1 T1 +V 220 Vrms 60 Hz 0° R2 5kQ D3 -V TS_POWER_10_TO_1 D4 (+

A: Bridge rectifier circuits are designed using diodes and thyristors. For uncontrolled rectification, ...

Q: 6.Given the circuit below, use Kirchoffs Voltage and Current Law to solve I1, l2 3Ω 42 40V 452 64V 2...

Q: A coil of resistance 20 ohms and inductance 200 microHenry is in parallel with a variable capacitor....

Q: The value of d26/dt2 for a synchronous machine, rated 50MVA, 60HZ, M = 1.02MJ.s/degree, and Pa = 3.5...

A: Given a synchronous machine having, Rated MVA, S = 50 MVA Frequency, f = 60 Hz Angular momentum, M=1...

Q: Q2 Figure Q2 shows a simple logic circuit. Figure Q2 Compute the simplified Boolean expression for o...

Q: For the three-way bulb (50 W, 100 W, 150 W), find the resistance of (a)the 100-W filament and (b) th...

Q: ) fit) in Fourier series in the interva) (-2, 2) when fct) = -2st <o %3D 1

Q: An analog voltage in the range 0 to 10.2 V is divided in 16 equal intervals for conversion to 4-bit ...

Q: Convert this to the form convenient for constructing Bode plots. That is, place the denominator fact...

Q: The number of the electric field lines, between two charged particles, is proportional to the amount...

Q: 7. A purely resistive lamp is rated at 200V (rms), 120 W (i.e., it dissipates 120 W power when conne...

A: Given, A purely resistive lamp, Vrms=200 VPrms=120 W

Q: (22)Use nodul analysıs to fin the power in (552) resis tor. [ 149.05 W) 15 i 252 Yu.52 125V- 8.2 55S...

A: The circuit are given as

Q: Q1) Determine the output (in frequency domain) of a LTI System having impulse response of h(n) = (-1...

Q: A coil of resistance 20 ohms and inductance 200 microHenry is in parallel with a variable capacitor....

A: This question belongs to circuit theory . It is based on the concept of resonance in parallel LC cir...

Q: 13. Find the missing values in Fig-33. = ? 1 = 0.8 A R, = ? V = 32 V 10 N 216 A R = ? Fig. 5-33

A: The solution is given below

Q: Provide 2 examples of open-loop and closed-loop control system. Identify the input, output, and proc...

Q: A generator is delivering power to infinite bus during post fault condition is 1.10 p.u at a power a...

A: Given: Delivering power to infinite bus during post fault condition, P = 1.10 p.u. Power angle, δ=60...

Q: Example: Find the reading of the voltmeter for the circuit below: 4Ω 4.42 = 180-66g ♡ 250 V 200 V 0....

A: Kirchoff's Law (KCL and KVL) and Ohm's law is very important to analyze electrical circuits. As per ...

Q: Compute the Laplace Transform of the following differential equations dy(t) (a) 3 + 3y(t) = u(t) dt ...

Q: 1. Properties of Linear Convolution include. Commutative %3D (u) Ix * (u)Tx= (u)7x * (u)'r Associati...

Q: IV-. From the circuit of common source JFET amplifier shown in the figure, its has VGs(om = -2.0V, I...

A: GIVEN: a circuit diagram VGS(off)=2.0VIDSS =1.4mAID =0.7mAVDD ...

Q: D2 С1 R1 5kQ V1 1n4001 1000µF T1 220 Vrms 60 Hz 0° +, TS POWER_10_TO_1

Q: The transfer function is, s(s² +s+2) G(s)H (s) = s+3s* +s +5s +10 Calculate the angle of arrival of ...

A: It is given that: G(s) H(s)=ss2+s+2s4+3s3+s2+5s+10

Q: 3) a) What is the logic function that is implemented by the gate in the below figure? b) What are th...

Q: Using 220kVA and 11kV as base values, express 138kV, 2MVA, 60A, and 660Ω as per unit values.

Q: A 200-MVA 15/200-kV single-phase power transformer has a resistance of 0.01352 and a reactance of 0....

A: Given, In single phase transformer the parameters are S=200 MVAV1/V2=15/200 kVR=0.0135 ΩX=0.0563 Ω

Q: + V4 - R4 R1 R3 16. R6 I 10 2 Is 6Ω 10 Ω + R5 R7 R$ 10 Ω V, E 100 V R2 30 Ω 6Ω 3 0

Q: Q2) The loop shown in Figure below is inside a uniform magnetic field B = 50ay mWb/m2. If side DC of...

A: It is given that: B=50aymWb/m2f=50Hzρ=6cm

Q: A 90MVA, 11KV water wheel generator has an inertia constant H = 3. The stored energy in the rotor at...

A: Given a water wheel generator has, MVA rating, S = 90 MVA Inertia constant, H = 3

Q: Example:find the current through the 10 ohm resistor.

Q: Explain State Space Representation of Nth order Linear Differential Equation.

A: Most physical systems can be modelled in terms of differential equations. So we need to devise a met...

Q: 7. Assuming an operating frequency of 1 kHz, transform the following phasor expressions into a singl...

Q: 10. Two resistances are connected in parallel. R1= 24Q, R2=24 Q, and IT=6 A. Find the current in eac...

Q: Three point charges are located as shown in the figure. q1 =-5 x 10-12 [C] and d = 6 [cm] 42 = -4 x ...

Q: Q3: Calculate thevalueof the currentshown in the below figure? 6mA w? 2mA 2A 3mA 7A 6A 1mA OA

Q: Discussion 1. Derive the transfer function of the (R-L-R) circuit, and then find the state space rep...

Q: al 10 D.

Q: An air core solenoid has a length of 10 cm and a cross-sectional area of 5 cm?. If it is wound with ...

Q: Answer the following. Use a detailed explanation. 1.What diode approximation has a voltage drop and...

Q: 16k 12K UK keL at Node O V, -Vz V, -V3 V, -12 6 18 kee at alode@ ューツ Vz- + 12 4 V3 12 KL ad alude G ...

A: In the solution provided, equation 1 is wrong.

Q: AB OD ol 11 101

Q: calculate the magnitude of the Thevenin Voltage. Assume that the j3 ohm inductor is the load. 1 of 1...

Concept explainers

Current Division Method

The generalized current divider formula is given by the following relation below,

Question

Solve for step by step process with complete solutions

Two alternating voltages are given by vị = 120 sin wt volts and v2
= 200 sin(wt --) volts. Obtain
%3D
the sinusoidal expression for v1 - v2 by resolution of phasors.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q5)-a)For this figure shown below the phase relationship between the sinusoidal waveform Of this set. -10sin(wt+80) V=15sin (wt+40) Q5)-b) for this circuit find the max energy if XL=100 Vm-300v,L=0.3H V= Vm Sinwt
Write a report to compare between Ac Through capacitance and AC through in inductance then: For the circuit shown beside, find the total impedance between a and b and Circuit current (I)
The capacitive reactance (XC).... be affected by the harmonics of non- * .sinusoidal wave will all-of-them O could O cannot O
18 In the circuit shown in the figure below, for what value of C will the current-I be in phase with the sinusoidal source voltage V= sin2t? Vs (1 + j1) Q (a) -F 4 (b) (c) (d) 1F /-
1. What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What effect does changing the amplitude on the effective value of sinusoidal voltage?
A sinusoidal current of 5 Arms is flowing through a series combination of a resistor and Inductor. The value of R is 45 ohms and that of the inductance is 15 mH and a frequency of 60 Hz. Find the magnitude and the phase angle of the voltage across the combination. (Hint: you can use phasor diagram). Select one: a. [V]=28.89, angle=9.39 b. IV]=25.60, angle367.00 c. [V]=128.01, angle3D10.18 d. IVl=226.77, angle=D7.16
Explain the following 1. Diffrence between DC and AC Electricity. 2. how to convert rectangular form to polar form and polar form to rectangular form. 3. why need to improve a power factor
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
For the phasor diagram in figure 6 express the voltages in sinusoids for a period of 5ms. Im Re )e,=45° e,=20 Vz=10 V2=8 Figure 7 a. Va(t)=. b. V2(t)=. c. What is the rms voltage of V1 = d. What is the rms voltage of V2=_ e. What is the frequency in Hz = f. What is the angular frequency =. In terms of lagging and leading what is the exact phase relationship between V, (t) and V2(t) g.